Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197659 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the front door outside handle assembly (for driver door). If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Driver Door)), or there may be wave interference.

WIRING DIAGRAM

B406563E03
5.344,0.74 5.958,0.938 0.615,0.198 10 false TSW1 5.333,1.406 5.948,1.604 0.615,0.198 10 false CLG5 5.333,2.125 5.948,2.323 0.615,0.198 10 false CG5B 5.865,1.833 6.479,2.031 0.615,0.198 10 false IC 6.021,0.271 6.635,0.469 0.615,0.198 10 false +B 6.25,2.344 6.865,2.542 0.615,0.198 10 false E 6.49,2.333 7.104,2.531 0.615,0.198 10 false G69 6.521,2.104 7.135,2.302 0.615,0.198 10 false 10 4.948,2.24 5.563,2.438 0.615,0.198 10 false G70 5,2.021 5.615,2.219 0.615,0.198 10 false 25 4.938,1.521 5.552,1.719 0.615,0.198 10 false G70 5.031,1.302 5.646,1.5 0.615,0.198 10 false 9 4.938,0.854 5.552,1.052 0.615,0.198 10 false G69 5.031,0.646 5.646,0.844 0.615,0.198 10 false 4 2.51,0.74 3.125,0.938 0.615,0.198 10 false 1 2.521,1.396 3.135,1.594 0.615,0.198 10 false 3 2.521,2.135 3.135,2.333 0.615,0.198 10 false 6 2.031,0.74 2.646,0.938 0.615,0.198 10 false TRG+ 1.146,0.74 1.76,0.938 0.615,0.198 10 false TRG- 0.969,0.74 1.583,0.938 0.615,0.198 10 false 4 2.042,1.406 2.656,1.604 0.615,0.198 10 false ANT1 2.031,2.135 2.646,2.333 0.615,0.198 10 false ANT2 0.958,2.844 2.167,3.042 1.208,0.198 10 false K8*1, J8*2 0.958,3.01 2.656,3.417 1.698,0.406 10 false Front Door Outside Handle Assembly (for Driver Door) 5.135,2.875 6.667,3.313 1.531,0.438 10 false Certification ECU (Smart Key ECU Assembly) 3.177,3.021 4.385,3.219 1.208,0.198 10 false *1: for LHD 3.188,3.302 4.396,3.5 1.208,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).

While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



HINT:
·

If the driver door entry lock and unlock functions do not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Radio Wave Interference
Parameter Name Cause of Problem and Countermeasure
Lock / Key RF Signal Interference When entry lock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry lock operation has been successfully performed, the possibility of wave interference is high.
Unlock / Key RF Signal Interference When entry unlock operation was performed, the electrical key transmitter sub-assembly could not be confirmed due to wave interference.
If the cause of the malfunction has not been stored but the vehicle has been moved and an entry unlock operation has been successfully performed, the possibility of wave interference is high.

PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window master switch is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Check the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A1 is not output.



Result:
Result Proceed to
DTC B27A1 is not output. A
DTC B27A1 is output. B



A

3.CHECK WAVE ENVIRONMENT

B

3.CHECK WAVE ENVIRONMENT
a.
B406013C02
2.781,1.188 3.094,1.385 0.313,0.198 10 false *a 0.021,0.021 0.333,0.219 0.313,0.198 12 false *A
*A for LHD
*a Approximately 0.3 m (0.984 ft.)


B406012C02
0.844,1.167 1.156,1.365 0.313,0.198 10 false *a 0.01,0.021 0.323,0.219 0.313,0.198 12 false *A
*A for RHD
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for Driver Door) and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B



A

4.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)

B

AFFECTED BY WAVE INTERFERENCE

4.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver door trigger switch ON or OFF ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed
·

Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
D-Door Trigger Switch
50003 125 12
OK:

On the GTS screen, the display changes between ON and OFF as shown in the table above.



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
5.CHECK KEY DIAGNOSTIC MODE
a.
B406013C02
2.781,1.188 3.094,1.385 0.313,0.198 10 false *a 0.021,0.021 0.333,0.219 0.313,0.198 12 false *A
*A for LHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


B406012C02
0.844,1.167 1.156,1.365 0.313,0.198 10 false *a 0.01,0.021 0.323,0.219 0.313,0.198 12 false *A
*A for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the front door outside handle assembly (for Driver Door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for Driver Door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
OK:

Wireless door lock buzzer sounds.




Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the G70 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K8*1 or J8*2 front door outside handle assembly (for Driver Door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G70-9 (CLG5) - K8-3 (ANT1) Always Below 1 Ω
G70-25 (CG5B) - K8-6 (ANT2) Always Below 1 Ω
G70-9 (CLG5) or K8-3 (ANT1) - Body ground Always 10 kΩ or higher
G70-25 (CG5B) or K8-6 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G70-9 (CLG5) - J8-3 (ANT1) Always Below 1 Ω
G70-25 (CG5B) - J8-6 (ANT2) Always Below 1 Ω
G70-9 (CLG5) or J8-3 (ANT1) - Body ground Always 10 kΩ or higher
G70-25 (CG5B) or J8-6 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
a.

Connect the K8*1 or J8*2 front door outside handle assembly (for Driver Door) connector.

*1: for LHD

*2: for RHD



b.

Connect the G70 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-10 (E) - Body ground Always Below 1 Ω



d.

Using an oscilloscope, check the waveform.

B418156C05
2.5,0.365 2.927,0.594 0.427,0.229 4.385,0.375 4.813,0.604 0.427,0.229 2.854,4.458 3.01,4.458 3.01,4.458 3.302,3.76 true 1.719,2.01 1.875,2.01 1.875,2.01 2.167,1.313 true 5.625,0.646 5.427,0.646 5.427,0.646 4.885,1.281 true 5.708,2.115 5.448,2.115 5.448,2.115 4.917,1.417 true 0.24,0.177 0.552,0.333 0.313,0.156 10 false *a 2.563,2.875 2.875,3.031 0.313,0.156 10 false *b 2.646,4.365 2.958,4.521 0.313,0.156 10 false *c 2.573,0.385 2.917,0.573 0.344,0.188 10 false G69 4.479,0.406 4.823,0.594 0.344,0.188 10 false G70 2.313,3.615 2.76,3.771 0.448,0.156 10 false GND 1.573,1.906 1.917,2.094 0.344,0.188 10 false E 5.771,2.021 6.333,2.219 0.563,0.198 10 false CG5B 5.688,0.542 6.25,0.74 0.563,0.198 10 false CLG5
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Trigger switch ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
G70-9 (CLG5) - G69-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door).


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
G70-25 (CG5B) - G69-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door).


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

10.CHECK ENTRY DOOR LOCK OPERATION
8.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the K8*1 or J8*2 front door outside handle assembly (for Driver Door) connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
K8-1 (TRG+) - G69-4 (TSW1) Always Below 1 Ω
K8-4 (TRG-) - Body ground Always Below 1 Ω
K8-1 (TRG+) or G69-4 (TSW1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J8-1 (TRG+) - G69-4 (TSW1) Always Below 1 Ω
J8-4 (TRG-) - Body ground Always Below 1 Ω
J8-1 (TRG+) or G69-4 (TSW1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Remove the front door outside handle assembly (for Driver Door).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL


b.

Inspect the front door outside handle assembly (for Driver Door).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK ENTRY DOOR LOCK OPERATION

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

10.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly (for Driver Door) before performing the inspection.


OK:

Entry lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)