Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197662 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine hood courtesy switch is installed together with the hood lock. This switch turns on when the engine hood is closed and turns off when the engine hood is opened.

WIRING DIAGRAM

E318154E03
5.323,0.948 5.938,1.146 0.615,0.198 10 false HCTY 5.042,0.948 5.656,1.146 0.615,0.198 10 false 20 3.813,0.938 4.427,1.135 0.615,0.198 10 false 12 3.542,2.01 5.125,2.427 1.583,0.417 10 false Instrument Panel Junction Block Assembly 5.542,2.958 6.156,3.156 0.615,0.198 10 false A 5.552,3.104 6.719,3.333 1.167,0.229 10 false Body ECU 2.938,0.948 3.552,1.146 0.615,0.198 10 false 2 1.333,1.354 1.948,1.552 0.615,0.198 10 false A34 1.563,0.948 2.177,1.146 0.615,0.198 10 false 1 1.323,1.51 3.188,1.917 1.865,0.406 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 3.552,1.844 4.167,2.042 0.615,0.198 10 false 2D 6.323,0.646 6.938,0.844 0.615,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.INSPECT ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
a.

Remove the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the A34 engine hood courtesy switch (hood lock assembly) connector.


b.

Disconnect the 2D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-2 - 2D-12 Always Below 1 Ω
A34-2 - Body ground Always 10 kΩ or higher
2D-12 - Body ground Always 10 kΩ or higher
A34-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343149C16
2.177,0.417 2.5,0.625 0.323,0.208 5.552,0.229 5.875,0.438 0.323,0.208 1.625,1.208 1.573,0.948 true 0.271,0.156 0.583,0.354 0.313,0.198 10 false *a 5.615,0.25 5.927,0.448 0.313,0.198 10 false 2D 2.292,0.438 2.604,0.635 0.313,0.198 10 false A 1.448,1.26 2.063,1.458 0.615,0.198 10 false HCTY
*a Component without harness connected (Instrument Panel Junction Block Assembly) - -


Standard Resistance:
Tester Connection Condition Specified Condition
2D-12 - A-20 (HCTY) Always Below 1 Ω



Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG (for LHD)
NG (for RHD)



OK (for LHD)

OK (for RHD)

NG (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY