Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33J0E _58 Vehicle Interior _038496 THEFT DETERRENT / KEYLESS ENTRY _0197662 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Door Courtesy Switch Circuit  


DESCRIPTION

The theft body ECU receives a door open or closed signal from front door courtesy light switch and combination meter assembly.

WIRING DIAGRAM

E318149E06
5.417,0.521 6.031,0.719 0.615,0.198 10 false ACTY 5.417,1.958 6.031,2.156 0.615,0.198 10 false DCTY 5.417,3.542 6.031,3.74 0.615,0.198 10 false PCTY 5.073,0.625 5.688,0.823 0.615,0.198 10 false A 5.073,2.073 5.688,2.271 0.615,0.198 10 false A 4.99,3.656 5.604,3.854 0.615,0.198 10 false G27 5.031,3.427 5.646,3.625 0.615,0.198 10 false 14 5.021,1.854 5.635,2.052 0.615,0.198 10 false 18 5.031,0.406 5.646,0.604 0.615,0.198 10 false 21 3.813,0.635 4.427,0.833 0.615,0.198 10 false 2Q 3.854,0.406 4.469,0.604 0.615,0.198 10 false 2 3.813,1.333 4.427,1.531 0.615,0.198 10 false 2Q 3.854,1.104 4.469,1.302 0.615,0.198 10 false 1 3.833,2.073 4.448,2.271 0.615,0.198 10 false 2L 3.865,1.865 4.479,2.063 0.615,0.198 10 false 4 2.875,1.958 3.49,2.156 0.615,0.198 10 false 1 1.844,2.333 3.302,2.625 1.458,0.292 10 false M9*1, *3, N2*2, *3 1.542,2.667 5.354,2.906 3.813,0.24 10 false Front Door Courtesy Light Switch Assembly (for Driver Side) 2.031,0.042 3.635,0.438 1.604,0.396 10 false Instrument Panel Junction Block Assembly 5.813,4.75 6.938,5 1.125,0.25 10 false Body ECU 1.927,3.885 3.615,4.125 1.688,0.24 10 false L9*1, *3, N1*2, *3 1.583,4.177 4.271,4.583 2.688,0.406 10 false Front Door Courtesy Light Switch Assembly (for Front Passenger Side) 2.333,4.708 4.75,5.042 2.417,0.333 10 false from Rear Door Courtesy Light Switch Assembly LH*5 2.333,5.271 5.833,5.5 3.5,0.229 10 false from Rear Door Courtesy Light Switch Assembly RH*5 0.063,5.844 1.01,6.042 0.948,0.198 10 false G10 0.052,6 1.917,6.25 1.865,0.25 10 false Combination Meter Assembly 2.177,6 4.094,6.26 1.917,0.26 10 false *1: for Smart Cab 2.188,6.313 4.063,6.521 1.875,0.208 10 false *2: except Smart Cab 3.656,5.99 5.594,6.24 1.938,0.25 10 false *3: for LHD 3.656,6.333 5.563,6.542 1.906,0.208 10 false *4: for RHD 0.688,0.635 1.302,0.833 0.615,0.198 10 false DOOR 0.719,1.313 1.333,1.51 0.615,0.198 10 false DCTY 0.729,3.198 1.344,3.396 0.615,0.198 10 false PCTY 0.594,4.667 1.208,4.865 0.615,0.198 10 false RLCY*5 0.583,5.281 1.198,5.479 0.615,0.198 10 false RRCY*5 1.25,0.521 1.865,0.719 0.615,0.198 10 false 12 1.25,1.219 1.865,1.417 0.615,0.198 10 false 15 1.25,3.083 1.865,3.281 0.615,0.198 10 false 16 1.25,4.552 1.865,4.75 0.615,0.198 10 false 17 1.25,5.167 1.865,5.365 0.615,0.198 10 false 18 2.885,3.552 3.5,3.75 0.615,0.198 10 false 1 6.604,0.219 6.917,0.417 0.313,0.198 10 false +B 6.615,1.667 6.927,1.865 0.313,0.198 10 false +B 6.615,3.229 6.927,3.427 0.313,0.198 10 false +B 1.844,2.49 3.219,2.75 1.375,0.26 10 false N1*2, *4 1.917,4.031 3.615,4.271 1.698,0.24 10 false N2*2, *4 4.656,5.99 6.531,6.198 1.875,0.208 10 false *5: except Single Cab

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK METER / GAUGE SYSTEM
a.

Check the meter / gauge system (door courtesy switch) is functioning normally.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result
OK
NG



OK

2.CHECK FRONT DOOR COURTESY SWITCH CIRCUIT

NG

2.CHECK FRONT DOOR COURTESY SWITCH CIRCUIT

b.

Connect the instrument panel junction block assembly connector.


c.

Disconnect the G10 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-18 (DCTY) - Body ground Driver side door closed (OFF) → Open (ON) 10 kΩ or higher → Below 1 Ω
G27-14 (PCTY) - Body ground Front passenger side door closed (OFF) → Open (ON) 10 kΩ or higher → Below 1 Ω



Result:
Proceed to
OK
NG (for Driver Side, LHD)
NG (for Driver Side, RHD)
NG (for Front Passenger Side)



OK

3.CHECK DOOR COURTESY SWITCH SIGNAL (ACTY)

NG (for Driver Side, LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for Driver Side, RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (for Front Passenger Side)

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DOOR COURTESY SWITCH SIGNAL (ACTY)
a.
B405277C01
0.167,0.896 0.542,1.156 0.375,0.26 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 0.271,0.927 0.583,1.125 0.313,0.198 10 false 2Q
*a Component with harness connected
(Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2Q-2 - Body ground All doors closed except driver door → Any door open except driver door 11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

b.

Connect the instrument panel junction block assembly connectors.


c.

Disconnect the G10 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-12 (DOOR) - A-21 (ACTY) Always Below 1 Ω
G10-12 (DOOR) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

5.CHECK BODY ECU

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.CHECK BODY ECU
a.

Disconnect the combination meter assembly connector.


b.
B405278C02
1.563,0.188 2.052,0.5 0.49,0.313 2.74,1.292 3.135,1.646 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.677,0.26 2.021,0.469 0.344,0.208 10 false G10 2.938,1.677 3.427,1.896 0.49,0.219 10 false DOOR
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G10-12 (DOOR) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG (for LHD)
NG (for RHD)



OK

REPLACE COMBINATION METER ASSEMBLY

NG (for LHD)

NG (for RHD)

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2Q instrument panel junction block assembly connector.


b.

Disconnect the G10 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-12 (DOOR) - 2Q-2 Always Below 1 Ω
G10-12 (DOOR) - Body ground Always 10 kΩ or higher



Result:
Result
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK (for RHD)

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR