When the transfer switches modes, the TL1, TL2 and TL3 terminals of the limit switch are in one of the ON/OFF combinations listed in the table below.
| Terminal | When H2 | Switching between H2 and H4 | When H4 | Switching between H4 and L4 | When L4 |
|---|---|---|---|---|---|
| TL1 | ON (GND) | ON (GND) | OFF (OPEN) | OFF (OPEN) | OFF (OPEN) |
| TL2 | OFF (OPEN) | OFF (OPEN) | OFF (OPEN) | ON (GND) | ON (GND) |
| TL3 | OFF (OPEN) | ON (GND) | ON (GND) | ON (GND) | OFF (OPEN) |
A malfunction is detected depending on the combination of the 3 circuits that make up the limit switch of the transfer shift actuator assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P17AC | Transfer Shift Motor Limit Switch Circuit | ·
Diagnosis Condition: Directly after the ignition switch is turned to ON, or while switching between H2 and H4 or while switching between H4 and L4 (transfer shift motor operating) with the ignition switch turned to ON ·
Malfunction Status: The combination of TL1, TL2 and TL3 does not match the pattern ·
Malfunction Time: 0 seconds ·
Other: 1 trip detection logic |
·
Wire harness and connector ·
4 wheel drive control ECU ·
Transfer shift actuator assembly |
Disconnect the C39 4 wheel drive control ECU connector.
Disconnect the C41 transfer shift actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C39-11 (TL1) - C41-3 (TL1) | Always | Below 1 Ω |
| C39-10 (TL2) - C41-4 (TL2) | Always | Below 1 Ω |
| C39-9 (TL3) - C41-5 (TL3) | Always | Below 1 Ω |
| C41-6 (GND1) - Body ground | Always | Below 1 Ω |
| C39-11 (TL1) or C41-3 (TL1) - Body ground | Always | 10 kΩ or higher |
| C39-10 (TL2) or C41-4 (TL2) - Body ground | Always | 10 kΩ or higher |
| C39-9 (TL3) or C41-5 (TL3) - Body ground | Always | 10 kΩ or higher |
| C39-11 (TL1) - C41-4 (TL2) and C41-5 (TL3) | Always | 10 kΩ or higher |
| C39-10 (TL2) - C41-3 (TL1) and C41-5 (TL3) | Always | 10 kΩ or higher |
| C39-9 (TL3) - C41-3 (TL1) and C41-4 (TL2) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transfer Shift Actuator Assembly) |
Disconnect the C41 transfer shift actuator assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-3 (TL1) - Body ground | Ignition switch ON | 10 to 14 V |
| C41-4 (TL2) - Body ground | Ignition switch ON | 10 to 14 V |
| C41-5 (TL3) - Body ground | Ignition switch ON | 10 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG