Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM33J0E _52 Drivetrain _038470 VF2CM TRANSFER / 4WD / AWD _0197772 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM D

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

When a DTC is stored, the 4 wheel drive control ECU stores the current vehicle state as Freeze Frame Data.

HINT:

Freeze Frame Data at the time a DTC is stored:

When the 4 wheel drive control ECU stores data at the time a DTC is stored, no updates will be performed until the data is cleared.




CHECK FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.

Powertrain > Four Wheel Drive > Trouble Codes
50001 363

f.

According to the display on the GTS, select the trouble code data display with Freeze Frame Data.

Powertrain > Four Wheel Drive
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.00 km/h (0.00 mph)
Max.: 327.67 km/h (203.61 mph)
Vehicle stopped: 0.00 km/h (0.00 mph) No large fluctuations when driving at a constant speed.
Front Differential Oil Temperature Front differential oil temperature Min.: -56°C (-69°F)
Min.: 199°C (390°F)
Displays front differential oil temperature -
4WD Control SW (LO) Transfer position switch status (transfer position switch input signal of LO terminal on ECU side) ON or OFF ON: H4 or L4
OFF: H2, between H2 and H4 or between H4 and L4
-
4WD Control SW (2-4) Transfer position switch status (transfer position switch input signal of 2-4 terminal on ECU side) ON or OFF ON: H2 or H4
OFF: Between H2 and H4, between H4 and L4 or L4
-
4WD Detection SW (4WD) Transfer shift actuator condition (4WD detection switch input signal of 4WD terminal on ECU side) ON or OFF ON: 4WD state
OFF: 2WD state
-
L4 Detection SW (4WDL) Transfer shift actuator condition (L4 detection switch input signal of 4WDL terminal on ECU side) ON or OFF ON: L4 state
OFF: State other than L4
-
ADD Position SW (ADD) A.D.D. actuator condition (A.D.D. position switch input signal of ADD terminal on ECU side) ON or OFF ON: A.D.D. actuator lock condition (4WD state)
OFF: A.D.D. actuator free condition (2WD state)
w/ A.D.D. Actuator
IG SW Ignition switch status ON or OFF ON: Ignition switch ON -
Transfer Limit SW (TL1) Transfer shift actuator limit switch (TL1) condition ON or OFF ON: H2 or switching between H2 and H4
OFF: H4, switching between H4 and L4 or L4
-
Transfer Limit SW (TL2) Transfer shift actuator limit switch (TL2) condition ON or OFF ON: Switching between H4 and L4 or L4
OFF: H2, switching between H2 and H4 or H4
-
Transfer Limit SW (TL3) Transfer shift actuator limit switch (TL3) condition ON or OFF ON: Switching between H2 and H4, H4 or switching between H4 and L4
OFF: H2 or L4
-
ADD Limit SW (DL1) A.D.D. actuator limit switch (DL1) condition ON or OFF ON: Free condition or switching between free and lock conditions
OFF: Lock condition
w/ A.D.D. Actuator
ADD Limit SW (DL2) A.D.D. actuator limit switch (DL2) condition ON or OFF ON: Switching between free and lock conditions or lock condition
OFF: Free condition
w/ A.D.D. Actuator
Clutch SW Clutch start switch status ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.
Shift SW Status (N Range) Shift lever neutral condition ON or OFF ON: Shift lever in N*1, shift lever in neutral*2
OFF: Shift lever not in N*1, shift lever not in neutral*2
-
Request Value of Vehicle Speed Limit 4WD vehicle speed limit request value Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle speed limit not requested: 200 km/h (124 mph) -
Transfer Shift Motor Target Current Target current for transfer shift motor driver circuit Min.: 0.0 A
Max.: 25.5 A
Normal: 0 A
Switching: 0 to 25.5 A
-
Transfer Shift Motor Actual Current Actual current of transfer shift motor driver circuit Min.: 0.0 A
Max.: 25.5 A
Normal: 0 A
Switching: 0 to 25.5 A
-
ADD Motor Target Current Target current for A.D.D. shift motor driver circuit Min.: 0.0 A
Max.: 25.5 A
Normal: 0 A
Switching: 0 to 25.5 A
w/ A.D.D. Actuator
ADD Motor Actual Current Actual current of A.D.D. shift motor driver circuit Min.: 0.0 A
Max.: 25.5 A
Normal: 0 A
Switching: 0 to 25.5 A
w/ A.D.D. Actuator
Motor Energization Status Signal Motor power signal status ON or OFF ON: Power supplied to motor
OFF: Power not supplied to motor
-
C/C Cancel Request Cruise control cancellation signal status ON or OFF ON: Cruise control cancellation requested
OFF: Cruise control cancellation not requested
-
4WD Status Signal 4WD status signal ON or OFF ON: 4WD state
OFF: 2WD state
-
L4 Status Signal L4 status signal ON or OFF ON: L4 state
OFF: State other than L4
-
Status of Transfer Shift Actuator Transfer shift actuator failure status Normal or Abnormal Normal: Actuator normal
Abnormal: Actuator abnormal
-
Buzzer Request Buzzer sounding request NO Sound, Sound(3 times) or Sound
·

NO Sound: Does not sound

·

Sound(3 times): Sounds 3 times

·

Sound: Sounds intermittently


·

Sounds 3 times: Sounds 3 times at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Sounds intermittently: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)


4WD Indicator Request 4WD indicator light (green/amber*3) request Blink(w/o MID)/ON(w/ MID), Blink(w/o MID)/OFF(w/ MID), Blink4*5, Blink3(w/o MID)/OFF(w/ MID), Blink2*5, Blink1, ON or OFF
·

Blink(w/o MID)/ON(w/ MID): Indicator light (amber) rapidly blinks*3 / Indicator light (green) illuminates*4

·

Blink(w/o MID)/OFF(w/ MID): Indicator light (amber) rapidly blinks*3 / Indicator light (green) turns off*4

·

Blink3(w/o MID)/OFF(w/ MID): Indicator light (amber) rapidly blinks*3 / Indicator light (green) turns off*4

·

Blink1: Indicator light (green) blinks

·

ON: Indicator light (green) illuminates

·

OFF: Indicator light (green/amber*3) turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


L4 Indicator Request 4LO indicator light request Blink4*5, Blink3, Blink2*5, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)


Multi-Terrain Select Control Multi-terrain select control signal OK or NG - This item is displayed but not used.
Vehicle Speed Limit Request 4WD vehicle speed limit request ON or OFF ON: Vehicle speed limiting is performed
OFF: Vehicle speed limiting is not performed
-
Transfer Motor Energization Request Transfer shift motor power supply command ON or OFF ON: Power supplied to transfer shift motor
OFF: Power not supplied to transfer shift motor
-
ADD Motor Energization Request A.D.D. shift motor power supply command ON or OFF ON: Power supplied to A.D.D. shift motor
OFF: Power not supplied to A.D.D. shift motor
w/ A.D.D. Actuator
IG Voltage IG monitor voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V: Ignition switch ON -
Motor Voltage Motor driver circuit monitor voltage Min.: 0.0 V
Max.: 25.5 V
Normal: 1.5 to 12.0 V
Switching: 3.5 V
-
Motor Duty Motor driver circuit duty Min.: 0%
Max.: 255%
Normal: 0%
Switching: 0 to 100%
-
Front Differential Oil Temperature Warning Count Count of front differential oil temperature warnings while ignition switch turned to ON Min.: 0 times
Max.: 255 times
Displays total number of oil temperature warnings -
Vehicle Speed Limit Request Count Count of 4WD vehicle speed limit requests while ignition switch turned to ON Min.: 0 times
Max.: 255 times
Displays total number of 4WD vehicle speed limit requests -
Mode Status Mode transition condition Initial Control, Particular Control at Start-Up, Shift Settling Control at Start-Up, H2, H2->H4L(T/F Activating), H2->H4L(ADD Activating), H4L->H2(T/F Activating), H4L->H2(ADD Activating), H4L, H4L->L4L, L4L->H4L, L4L Rr Diff. Free, H4F->L4F, L4F->H4F, H4F, H4F->H4L, H4L->H4F, L4F, L4L Rr Diff. Free->Lock, L4L Rr Diff. Lock->Free, L4L Rr Diff. Lock, K1, K2, K3, K4, K5, K6, K7, K8, K9, K10, S01, S02, S03, S04, S05, S06, S07, S08, S09, S10, S11, S12, S13, S14, S15, S16, S17, S18, S19, S20, S21, S22, S23, S24, B1, B2, B3, B4, B5, B6, 2WD Rr Diff. Free, 2WD Rr Diff. Free->Lock, 2WD Rr Diff. Lock->Free or 2WD Rr Diff. Lock Displays transfer shift actuator, A.D.D. actuator*8 and differential lock coil*7 transition conditions
HINT:
·

K1 to K10: Control while switching prohibited

·

S01 to S24: Control while switching limited

·

B1 to B6: Control while switching again



Oil Temperature Sensor Mode Oil temperature sensor detection mode Low Temperature Mode or High Temperature Mode Low Temperature Mode: Detecting oil temperature in low temperature mode
High Temperature Mode: Detecting oil temperature in high temperature mod
-
Motor Relay (RY1-1) Internal ECU relay (RY1-1) condition*6 ON or OFF ON: Relay on
OFF: Relay off
-
Motor Relay (RY1-2) Internal ECU relay (RY1-2) condition*6 ON or OFF ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-1) Internal ECU relay (RY2-1) condition*6 ON or OFF ON: Relay on
OFF: Relay off
-
Motor Relay (RY2-2) Internal ECU relay (RY2-2) condition*6 ON or OFF ON: Relay on
OFF: Relay off
-
AT/MT AT or MT identification AT or MT AT: Automatic transmission
MT: Manual transmission
-
CAN Signal Invalid Status by IG Voltage Low Whether CAN communication data invalid condition due to IG voltage drop Valid or Inval Valid: IG voltage 9.5 V or higher Inval: IG voltage below 9.5 V
SW Input Invalid Status by IG Voltage Low Input invalid condition of switches inside actuator due to IG voltage drop Valid or Inval Valid: IG voltage 7.1 V or higher Inval: IG voltage below 7.1 V
Transfer Shift Invalid Status by IG Voltage Low Transfer shift actuator switching operation invalid condition due to IG voltage drop Valid or Inval Valid: IG voltage 9.5 V or higher Inval: IG voltage below 9.5 V
Number of DTC Number of DTCs stored Min.: 0
Max.: 255
0 -

*1: for Automatic Transmission

*2: for Manual Transmission

*3: w/o Multi-information Display

*4: w/ Multi-information Display

*5: Item not supported, therefore not displayed

*6: For the position of the relay, refer to the P17A9 wiring diagram.

Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>P17A9

*7: w/ Differential Lock

*8: w/ A.D.D. Actuator




CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.