To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1.DRAIN ENGINE COOLANT
17410
2.REMOVE FRONT EXHAUST PIPE ASSEMBLY
3.REMOVE FUEL ADDITION INJECTOR ASSEMBLY
53882F
4.REMOVE FRONT FENDER SEAL
for 2WD:
Remove the 5 clips and front fender seal from the body.
for 4WD and Pre-Runner:
Remove the 6 clips and front fender seal from the body.
5.REMOVE AIR CLEANER CAP AND HOSE
17801
6.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
7.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
89481B
8.REMOVE DIFFERENTIAL PRESSURE SENSOR
89425
9.REMOVE EXHAUST GAS TEMPERATURE SENSOR
25733A
10.REMOVE NO. 1 VACUUM PIPE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.
Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.
25734
11.REMOVE NO. 2 VACUUM PIPE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.
Remove the clamp from the pipe clamp.
17578B
12.REMOVE PIPE CLAMP
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 3 bolts and pipe clamp from the engine cover bracket.
12631A
13.REMOVE ENGINE COVER BRACKET
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Detach the 2 clamp and disconnect the engine wire from the engine cover bracket.
Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.
48691
14.REMOVE UPPER ARM BUSH HEAT INSULATOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 2 bolt and upper arm bush heat insulator from the body.
89467B
15.REMOVE AIR FUEL RATIO SENSOR
17167
16.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
17271
17.REMOVE NO. 1 TURBO INSULATOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger sub-assembly.
17118
18.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.
17118
19.REMOVE EXHAUST PIPE SUPPORT STAY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.
25051
20.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.
Remove the gasket.