To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assemblies do not need to be removed when inspecting the valve clearance.
11201
1.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
2.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Matchmark |
Align the matchmarks of the crankshaft pulley and timing gear cover by rotating the crankshaft clockwise.
Make sure that both cam lobes (intake side and exhaust side) of the No. 1 cylinder face upward.
3.INSPECT VALVE CLEARANCE
| *a | Front |
| *b | Exhaust |
| *c | Intake |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.
| Item | Specified Condition |
|---|---|
| Intake | 0.2 to 0.3 mm (0.00787 to 0.0118 in.) |
| Exhaust | 0.35 to 0.45 mm (0.0138 to 0.0177 in.) |
Write down any valve clearance measurements that are not within the specified range. These measurements will be used later to determine the size of the adjustment valve lifter to be installed.
Turn the crankshaft 360° to set the No. 4 cylinder to TDC/compression.
| *a | Front |
| *b | Exhaust |
| *c | Intake |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft sub-assembly.
| Item | Specified Condition |
|---|---|
| Intake | 0.2 to 0.3 mm (0.00787 to 0.0118 in.) |
| Exhaust | 0.35 to 0.45 mm (0.0138 to 0.0177 in.) |
Write down any valve clearance measurements that are not within the specified range. These measurements will be used later to determine the size of the adjustment valve lifter to be installed.
4.ADJUST VALVE CLEARANCE
Remove the camshaft sub-assemblies.
Click hereEngine / Hybrid System>2KD-FTV ENGINE MECHANICAL>CAMSHAFT>REMOVAL
Remove the valve lifters.
Using a micrometer, measure the thickness of the removed valve lifter.
Calculate the thickness of a new lifter so that the valve clearance is within the specified range.
| A | B | C |
|---|---|---|
| New valve lifter thickness | Used valve lifter thickness | Measured valve clearance |
Intake: A = B + (C - 0.25 mm (0.00984 in.))
Exhaust: A = B + (C - 0.40 mm (0.0157 in.))
Select a new valve lifter with a thickness as close as possible to the calculated values.
Valve lifters are available in 35 sizes in increments of 0.02 mm (0.000787 in.), from 5.06 mm (0.199 in.) to 5.74 mm (0.226 in.).
Install the selected valve lifter.
| *a | Valve Lifter Selection Chart (Intake) | *b | Measured clearance mm (in.) |
| *c | Installed lifter thickness mm (in.) | - | - |
0.2 to 0.3 mm (0.00787 to 0.0118 in.)
A 5.25 mm (0.207 in.) lifter is installed, and the measured clearance is 0.4 mm (0.0157 in.). Replace the 5.25 mm (0.207 in.) lifter with a No. 40 lifter.
| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
|---|---|---|---|---|---|
| 06 | 5.06 mm (0.1992 in.) | 30 | 5.30 mm (0.2087 in.) | 54 | 5.54 mm (0.2181 in.) |
| 08 | 5.08 mm (0.2000 in.) | 32 | 5.32 mm (0.2094 in.) | 56 | 5.56 mm (0.2189 in.) |
| 10 | 5.10 mm (0.2008 in.) | 34 | 5.34 mm (0.2102 in.) | 58 | 5.58 mm (0.2197 in.) |
| 12 | 5.12 mm (0.2016 in.) | 36 | 5.36 mm (0.2110 in.) | 60 | 5.60 mm (0.2205 in.) |
| 14 | 5.14 mm (0.2024 in.) | 38 | 5.38 mm (0.2118 in.) | 62 | 5.62 mm (0.2213 in.) |
| 16 | 5.16 mm (0.2031 in.) | 40 | 5.40 mm (0.2126 in.) | 64 | 5.64 mm (0.2220 in.) |
| 18 | 5.18 mm (0.2039 in.) | 42 | 5.42 mm (0.2134 in.) | 66 | 5.66 mm (0.2228 in.) |
| 20 | 5.20 mm (0.2047 in.) | 44 | 5.44 mm (0.2142 in.) | 68 | 5.68 mm (0.2236 in.) |
| 22 | 5.22 mm (0.2055 in.) | 46 | 5.46 mm (0.2150 in.) | 70 | 5.70 mm (0.2244 in.) |
| 24 | 5.24 mm (0.2063 in.) | 48 | 5.48 mm (0.2157 in.) | 72 | 5.72 mm (0.2252 in.) |
| 26 | 5.26 mm (0.2071 in.) | 50 | 5.50 mm (0.2165 in.) | 74 | 5.74 mm (0.2260 in.) |
| 28 | 5.28 mm (0.2079 in.) | 52 | 5.52 mm (0.2173 in.) | - | - |
| *a | Valve Lifter Selection Chart (Exhaust) | *b | Measured clearance mm (in.) |
| *c | Installed lifter thickness mm (in.) | - | - |
0.35 to 0.45 mm (0.0138 to 0.0177 in.)
A 5.34 mm (0.210 in.) lifter is installed, and the measured clearance is 0.48 mm (0.0189 in.). Replace the 5.34 mm (0.210 in.) lifter with a No. 42 lifter.
| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
|---|---|---|---|---|---|
| 06 | 5.06 mm (0.1992 in.) | 30 | 5.30 mm (0.2087 in.) | 54 | 5.54 mm (0.2181 in.) |
| 08 | 5.08 mm (0.2000 in.) | 32 | 5.32 mm (0.2094 in.) | 56 | 5.56 mm (0.2189 in.) |
| 10 | 5.10 mm (0.2008 in.) | 34 | 5.34 mm (0.2102 in.) | 58 | 5.58 mm (0.2197 in.) |
| 12 | 5.12 mm (0.2016 in.) | 36 | 5.36 mm (0.2110 in.) | 60 | 5.60 mm (0.2205 in.) |
| 14 | 5.14 mm (0.2024 in.) | 38 | 5.38 mm (0.2118 in.) | 62 | 5.62 mm (0.2213 in.) |
| 16 | 5.16 mm (0.2031 in.) | 40 | 5.40 mm (0.2126 in.) | 64 | 5.64 mm (0.2220 in.) |
| 18 | 5.18 mm (0.2039 in.) | 42 | 5.42 mm (0.2134 in.) | 66 | 5.66 mm (0.2228 in.) |
| 20 | 5.20 mm (0.2047 in.) | 44 | 5.44 mm (0.2142 in.) | 68 | 5.68 mm (0.2236 in.) |
| 22 | 5.22 mm (0.2055 in.) | 46 | 5.46 mm (0.2150 in.) | 70 | 5.70 mm (0.2244 in.) |
| 24 | 5.24 mm (0.2063 in.) | 48 | 5.48 mm (0.2157 in.) | 72 | 5.72 mm (0.2252 in.) |
| 26 | 5.26 mm (0.2071 in.) | 50 | 5.50 mm (0.2165 in.) | 74 | 5.74 mm (0.2260 in.) |
| 28 | 5.28 mm (0.2079 in.) | 52 | 5.52 mm (0.2173 in.) | - | - |
Install the camshaft sub-assemblies.
Click hereEngine / Hybrid System>2KD-FTV ENGINE MECHANICAL>CAMSHAFT>INSTALLATION
5.INSPECT FOR COOLANT LEAK
6.BLEED AIR FROM FUEL SYSTEM
7.INSPECT FOR FUEL LEAK
8.INSPECT FOR OIL LEAK