Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM33J0E _51 Engine / Hybrid System _038437 2GD-FTV ENGINE CONTROL _0201524 ECD SYSTEM(w/ DPF) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal sensor assembly.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0.5 V and 4.8 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

A255815E39
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.854,2.875 0.5,3.333 true 1.052,2.26 1.302,1.375 1.302,1.375 1.417,1.375 true 4.333,1.833 3.844,0.938 false 1.021,2.542 0.927,1.844 0.927,1.844 0.844,1.844 true 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.302 1.938,1.479 0.479,0.177 10 false Magnet 0.313,1.76 0.844,1.938 0.531,0.177 10 false IC No. 1 0.313,3.344 0.844,3.521 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.656,3.938 6.76,4.167 2.104,0.229 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V and VPA2 is more than 2.7 deg, or VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

VPA circuit open or shorted to ground

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is higher than 4.8 V.
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V.
(b) VPA is more than 2.7 deg.
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

VPA2 circuit open or shorted to ground

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is higher than 4.8 V.
(b) VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Conditions (a) or (b) continue for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is less than 0.02 V.
(b) VPA is below 0.4 V and VPA2 is below 1.2 V.
·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2120
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %


P2122
P2123
P2125
P2127
P2128
P2138

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2120 Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds


P2122
P2123
P2125
P2127
P2128
P2138

WIRING DIAGRAM

A348544E02
0.396,3.052 0.854,3.25 0.458,0.198 10 false A41 0.375,3.229 3.177,3.583 2.802,0.354 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 5.906,3.052 6.365,3.25 0.458,0.198 10 false G86 5.917,3.24 6.375,3.438 0.458,0.198 10 false ECM 1.604,0.542 2.063,0.74 0.458,0.198 10 false VPA 1.594,0.969 2.052,1.167 0.458,0.198 10 false EPA 1.51,1.396 2.219,1.615 0.708,0.219 10 false VCPA 1.531,1.802 1.99,2 0.458,0.198 10 false VPA2 1.531,2.219 1.99,2.417 0.458,0.198 10 false EPA2 1.531,2.635 1.99,2.833 0.458,0.198 10 false VCP2 2,2.74 2.458,2.938 0.458,0.198 10 false 1 2,2.333 2.458,2.531 0.458,0.198 10 false 2 2.01,1.927 2.469,2.125 0.458,0.198 10 false 3 2.01,1.479 2.469,1.677 0.458,0.198 10 false 4 2.01,1.083 2.469,1.281 0.458,0.198 10 false 5 1.99,0.656 2.448,0.854 0.458,0.198 10 false 6 5.333,0.646 5.792,0.844 0.458,0.198 10 false 28 5.323,1.073 5.781,1.271 0.458,0.198 10 false 22 5.333,1.5 5.792,1.698 0.458,0.198 10 false 29 5.333,1.917 5.792,2.115 0.458,0.198 10 false 31 5.333,2.333 5.792,2.531 0.458,0.198 10 false 25 5.333,2.75 5.792,2.948 0.458,0.198 10 false 30 5.615,2.521 6.073,2.719 0.458,0.198 10 false VCP2 5.583,2.094 6.042,2.292 0.458,0.198 10 false EPA2 5.594,1.667 6.052,1.865 0.458,0.198 10 false VPA2 5.594,1.229 6.302,1.448 0.708,0.219 10 false VCPA 5.594,0.833 6.052,1.031 0.458,0.198 10 false EPA 5.615,0.417 6.073,0.615 0.458,0.198 10 false VPA

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCEL SENS.)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 234 15,16

d.
C129061C03
0.833,1.594 1.042,1.802 0.208,0.208 10 false *a 0.271,0.323 0.479,0.531 0.208,0.208 10 false *1 2.24,1.594 2.5,1.802 0.26,0.208 10 false *b
*1 Accelerator Pedal Assembly
*a Depressed
*b Released


Read the values.

Standard:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%



Result:
Result Proceed to
NG A
OK B



A

2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)
a.
A257437C89
2.792,0.917 3.156,1.167 0.365,0.25 2.292,2.406 2.865,1.688 true 1.552,2.417 2.833,1.646 true 2.792,2.396 3,1.698 true 2.385,0.896 2.49,0.896 2.49,0.896 3.042,1.635 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.708,2.427 2.479,2.708 0.771,0.281 10 false 30 (VCP2) 0.917,2.417 1.698,2.635 0.781,0.219 10 false 25 (EPA2) 2.438,2.427 3.26,2.667 0.823,0.24 10 false 29 (VCPA) 1.771,0.813 2.469,1.073 0.698,0.26 10 false 22 (EPA) 2.844,0.958 3.208,1.229 0.365,0.271 10 false G86
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G86-29 (VCPA) - G86-22 (EPA) Ignition switch ON 4.5 to 5.5 V
G86-30 (VCP2) - G86-25 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT ACCELERATOR PEDAL POSITION SENSOR (VPA, VPA2 VOLTAGE)

NG

10.REPLACE ECM
3.INSPECT ACCELERATOR PEDAL POSITION SENSOR (VPA, VPA2 VOLTAGE)
a.
A257437C90
2.802,0.906 3.167,1.156 0.365,0.25 2.271,2.354 2.823,1.698 true 1.833,2.365 2.823,1.635 true 2.25,0.969 2.344,0.969 2.344,0.969 3.042,1.635 true 3.052,2.354 3.042,1.698 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 2.708,2.417 3.385,2.646 0.677,0.229 10 false 28 (VPA) 1.25,2.406 2.031,2.635 0.781,0.229 10 false 25 (EPA2) 1.635,0.865 2.458,1.104 0.823,0.24 10 false 22 (EPA) 1.979,2.406 2.865,2.667 0.885,0.26 10 false 31 (VPA2) 2.865,0.948 3.229,1.219 0.365,0.271 10 false G86
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G86-28 (VPA) - G86-22 (EPA) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.0 to 4.6 V
G86-31 (VPA2) - G86-25 (EPA2) Ignition switch ON, accelerator pedal fully released 0.9 to 2.3 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 5.0 V



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.
A194124C50
0.25,2.188 0.719,2.448 0.469,0.26 0.948,3.094 1.417,2.458 true 1.281,2.438 0.771,2.823 true 2.01,3.115 1.885,2.469 true 1.729,2.458 1.542,3.115 true 0.219,0.188 0.76,0.552 0.542,0.365 10 false *a 1.938,3.125 2.521,3.427 0.583,0.302 10 false EPA 0.688,3.125 1.365,3.427 0.677,0.302 10 false EPA2 0.375,2.781 1.031,3.104 0.656,0.323 10 false VCP2 1.323,3.125 1.927,3.427 0.604,0.302 10 false VCPA 0.375,2.24 0.698,2.5 0.323,0.26 10 false A41
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A41-4 (VCPA) - A41-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A41-1 (VCP2) - A41-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the accelerator pedal sensor assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-6 (VPA) - G86-28 (VPA) Always Below 1 Ω
A41-5 (EPA) - G86-22 (EPA) Always Below 1 Ω
A41-3 (VPA2) - G86-31 (VPA2) Always Below 1 Ω
A41-2 (EPA2) - G86-25 (EPA2) Always Below 1 Ω
A41-6 (VPA) or G86-28 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A41-5 (EPA) or G86-22 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A41-3 (VPA2) or G86-31 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A41-2 (EPA2) or G86-25 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the accelerator pedal sensor assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.
A257437C91
2.771,0.896 3.146,1.156 0.375,0.26 1.49,2.417 2.823,1.698 true 2.875,1.708 2.188,2.427 true 2.833,2.417 3,1.708 true 2.156,0.604 2.26,0.604 2.26,0.604 3.042,1.646 true 2.146,0.958 2.26,0.958 2.26,0.958 2.823,1.646 true 3.125,2.885 3.042,1.698 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.885,2.448 1.667,2.656 0.781,0.208 10 false 31 (VPA2) 1.469,0.875 2.219,1.083 0.75,0.208 10 false 25 (EPA2) 2.323,2.448 3.104,2.635 0.781,0.188 10 false 29 (VCPA) 2.698,2.927 3.375,3.188 0.677,0.26 10 false 28 (VPA) 2.833,0.938 3.198,1.208 0.365,0.271 10 false G86 1.604,2.448 2.51,2.74 0.906,0.292 10 false 30 (VCP2) 1.552,0.531 2.198,0.771 0.646,0.24 10 false 22 (EPA)
*a Component with harness connected
(ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G86-29 (VCPA) - G86-28 (VPA) Ignition switch off No short or open circuit
G86-28 (VPA) - G86-22 (EPA) Ignition switch off No short or open circuit
G86-30 (VCP2) - G86-31 (VPA2) Ignition switch off No short or open circuit
G86-31 (VPA2) - G86-25 (EPA2) Ignition switch off No short or open circuit



c.

Reconnect the accelerator pedal sensor assembly connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

10.REPLACE ECM
7.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and leave the vehicle for 30 seconds.


d.

Turn the ignition switch to ON.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED