Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2015.11
RM33J0E _59 Vehicle Exterior _038498 LIGHTING (EXT) _0219141 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B2416  Height Control Sensor Malfunction  


DESCRIPTION

This DTC is stored when the headlight leveling ECU assembly detects a malfunction in the rear height control sensor sub-assembly LH power source or rear height control sensor sub-assembly LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2416 Height Control Sensor Malfunction
·

Malfunction in rear height control sensor sub-assembly LH

·

Open or short in rear height control sensor sub-assembly LH power source circuit


·

Rear height control sensor sub-assembly LH

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E317276E03
2.385,0.906 2.844,1.104 0.458,0.198 10 false SHB 2.365,1.385 2.823,1.583 0.458,0.198 10 false SHG 2.792,0.771 3.25,0.969 0.458,0.198 10 false 3 2.813,1.313 3.271,1.51 0.458,0.198 10 false 1 0.948,1.958 1.406,2.156 0.458,0.198 10 false O7 0.927,2.125 3.906,2.323 2.979,0.198 10 false Rear Height Control Sensor Sub-assembly LH 4.271,0.802 4.729,1 0.458,0.198 10 false SBR 4.281,1.313 4.74,1.51 0.458,0.198 10 false SGR 3.99,0.771 4.448,0.969 0.458,0.198 10 false 12 4,1.292 4.458,1.49 0.458,0.198 10 false 21 4.167,1.917 4.625,2.115 0.458,0.198 10 false G80 4.198,2.083 6.51,2.302 2.313,0.219 10 false Headlight Leveling ECU Assembly 4.969,0.646 5.427,0.844 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

If any of the following are performed, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

Replacement of the rear height control sensor sub-assembly LH

·

Removal/installation of the rear height control sensor sub-assembly LH

·

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC B2416 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the display on the GTS.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Height control sensor power supply value 0.00 to 5.00 V 4.61 to 5.00 V -
Body Electrical > HL AutoLeveling > Data List
Tester Display
Height Sens Pw Supply Val
50003 361 6
OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the G80 headlight leveling ECU assembly connector.


b.

Disconnect the O7 rear height control sensor sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-12 (SBR) - O7-3 (SHB) Always Below 1 Ω
G80-21 (SGR) - O7-1 (SHG) Always Below 1 Ω
G80-12 (SBR) - Body ground Always 10 kΩ or higher
G80-21 (SGR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH