The headlight leveling ECU assembly actuates the headlight leveling motors according to vehicle conditions.
If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test of the leveling motors.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Leveling motor upward or downward operation | Stop/Down/Up | Perform the Active Test with the engine started and vehicle stopped |
| Tester Display |
|---|
| Drive The Leveling Motor |
Headlight leveling motors operate normally.
| Proceed to |
|---|
| OK |
| NG (for LH Side) |
| NG (for RH Side) |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG (for LH Side)
NG (for RH Side)
Disconnect the G80 headlight leveling ECU assembly connector.
Disconnect the A28 headlight leveling motor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-11 (LH+) - A28-3 (LHIG) | Always | Below 1 Ω |
| G80-18 (LHT) - A28-2 (LH T) | Always | Below 1 Ω |
| G80-24 (LH-) - A28-1 (LH E) | Always | Below 1 Ω |
| G80-11 (LH+) - Body ground | Always | 10 kΩ or higher |
| G80-18 (LHT) - Body ground | Always | 10 kΩ or higher |
| G80-24 (LH-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight leveling motor LH with a new or known good one.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>DISASSEMBLY
Perform the Active Test of the leveling motor.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Leveling motor upward or downward operation | Stop/Down/Up | Perform the Active Test with the engine started and vehicle stopped |
| Tester Display |
|---|
| Drive The Leveling Motor |
Headlight leveling motor LH operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G80 headlight leveling ECU assembly connector.
Disconnect the A27 headlight leveling motor RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G80-10 (RH+) - A27-3 (RHIG) | Always | Below 1 Ω |
| G80-17 (RHT) - A27-2 (RH T) | Always | Below 1 Ω |
| G80-23 (RH-) - A27-1 (RH E) | Always | Below 1 Ω |
| G80-10 (RH+) - Body ground | Always | 10 kΩ or higher |
| G80-17 (RHT) - Body ground | Always | 10 kΩ or higher |
| G80-23 (RH-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight leveling motor RH with a new or known good one.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>DISASSEMBLY
Perform the Active Test of the leveling motor.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor | Leveling motor upward or downward operation | Stop/Down/Up | Perform the Active Test with the engine started and vehicle stopped |
| Tester Display |
|---|
| Drive The Leveling Motor |
Headlight leveling motor RH operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG