Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.11
RM33J0E _56 Audio / Visual / Telematics _044808 NAVIGATION / MULTI INFO DISPLAY _0219999 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E317099E03
0.656,0.344 1.271,0.542 0.615,0.198 10 false UGD1 0.656,0.781 1.271,0.979 0.615,0.198 10 false US1+ 0.667,1.208 1.281,1.406 0.615,0.198 10 false US1- 0.677,1.656 1.292,1.854 0.615,0.198 10 false USV1 0.656,2.083 1.271,2.281 0.615,0.198 10 false USG1 0.052,2.802 1.729,3.167 1.677,0.365 10 false No. 1 Stereo Jack Adapter Assembly 0.094,3.427 1.031,3.604 0.938,0.177 10 false *: Shielded 2.573,2.26 3.51,2.427 0.938,0.167 10 false * 4.51,2.25 5.448,2.417 0.938,0.167 10 false * 3.094,2.5 3.854,2.667 0.76,0.167 10 false Radio Wire 6.146,0.344 6.76,0.542 0.615,0.198 10 false UGD1 6.125,0.802 6.74,1 0.615,0.198 10 false US1+ 6.135,1.229 6.75,1.427 0.615,0.198 10 false US1- 6.146,1.667 6.76,1.865 0.615,0.198 10 false USV1 6.167,2.125 6.781,2.323 0.615,0.198 10 false USG1 5.865,2.781 7.094,3.094 1.229,0.313 10 false Navigation Receiver Assembly 1.156,0.688 1.354,0.854 0.198,0.167 10 false 3 1.167,1.125 1.365,1.292 0.198,0.167 10 false 2 1.156,1.573 1.354,1.74 0.198,0.167 10 false 1 1.167,1.99 1.365,2.156 0.198,0.167 10 false 5 0.063,2.625 0.26,2.792 0.198,0.167 10 false a1 5.854,2.615 6.208,2.781 0.354,0.167 10 false a3 1.167,0.26 1.365,0.427 0.198,0.167 10 false 4 5.927,0.26 6.125,0.427 0.198,0.167 10 false 4 5.927,0.688 6.125,0.854 0.198,0.167 10 false 3 5.938,1.125 6.135,1.292 0.198,0.167 10 false 2 5.927,1.563 6.125,1.729 0.198,0.167 10 false 1 5.927,1.99 6.125,2.156 0.198,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:
·

When a large amount of data is in a USB device, it may take a while to before play begins.

·

When using a USB device, files that are copy protected or encrypted cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION



Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B



A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK RADIO WIRE
2.CHECK RADIO WIRE
a.

Disconnect the a1 No. 1 stereo jack adapter assembly connector.


b.
E317100C03
1.438,0.156 1.844,0.406 0.406,0.25 1.458,1.76 1.865,2.01 0.406,0.25 1.083,1.333 1.542,1.01 true 1.083,0.781 1.49,0.906 true 1.115,0.531 1.583,0.906 true 1.708,0.906 2.281,0.375 true 1.823,0.906 2.302,0.677 true 1.563,2.573 1.125,2.375 true 1.552,2.698 1.135,2.833 true 2.188,2.708 1.74,2.688 true 2.219,2.365 1.719,2.573 true 2.198,3.083 1.698,2.802 true 0.188,0.135 0.406,0.323 0.219,0.188 10 false *a 0.26,1.99 0.479,2.177 0.219,0.188 10 false *b 1.563,0.188 1.76,0.354 0.198,0.167 10 false a1 1.594,1.802 1.792,1.969 0.198,0.167 10 false a3 2.344,0.615 2.76,0.771 0.417,0.156 10 false UGD1 2.333,0.271 2.75,0.427 0.417,0.156 10 false US1+ 0.76,0.406 1.177,0.563 0.417,0.156 10 false US1- 0.677,0.719 1.094,0.875 0.417,0.156 10 false USV1 0.688,1.292 1.104,1.448 0.417,0.156 10 false USG1 0.74,2.219 1.156,2.375 0.417,0.156 10 false UGD1 0.75,2.76 1.167,2.917 0.417,0.156 10 false US1+ 2.271,2.625 2.688,2.781 0.417,0.156 10 false US1- 2.271,2.25 2.688,2.406 0.417,0.156 10 false USV1 2.25,3.021 2.667,3.177 0.417,0.156 10 false USG1
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the a3 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-4 (UGD1) - a3-4 (UGD1) Always Below 1 Ω
a1-3 (US1+) - a3-3 (US1+) Always Below 1 Ω
a1-2 (US1-) - a3-2 (US1-) Always Below 1 Ω
a1-1 (USV1) - a3-1 (USV1) Always Below 1 Ω
a1-5 (USG1) - a3-5 (USG1) Always Below 1 Ω
a1-4 (UGD1) - Body ground Always 10 kΩ or higher
a1-3 (US1+) - Body ground Always 10 kΩ or higher
a1-2 (US1-) - Body ground Always 10 kΩ or higher
a1-1 (USV1) - Body ground Always 10 kΩ or higher
a1-5 (USG1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the No. 1 stereo jack adapter assembly connector.


b.
E278189C12
0.563,0.896 1.021,1.146 0.458,0.25 0.875,0.5 1.125,0.5 1.125,0.5 1.49,0.875 true 2.583,0.5 2.333,0.5 2.333,0.5 1.917,0.875 true 0.719,0.938 1.063,1.156 0.344,0.219 10 false a1 0.052,0.052 0.396,0.271 0.344,0.219 10 false *a 0.385,0.427 1.063,0.594 0.677,0.167 10 false USV1 2.625,0.417 3.125,0.667 0.5,0.25 10 false UGD1
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a1-1 (USV1) - a1-4 (UGD1) Ignition switch ACC 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.



b.

Save the data again and check if it can be played on the in-vehicle device.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (USB OR "iPod" IS DEFECTIVE)

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if USB device or "iPod" is recognized by navigation receiver, or if information such as track, artist and album names are displayed on screen.

OK:

USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE