The display signal from the rear television camera assembly is transmitted to the navigation receiver assembly.
When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Service.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Disconnect the G117 navigation receiver assembly connector.
Disconnect the P2 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G117-11 (CA+) - P2-6 (CB+) | Always | Below 1 Ω |
| G117-12 (V+) - P2-3 (CV+) | Always | Below 1 Ω |
| G117-23 (CGND) - P2-5 (CGND) | Always | Below 1 Ω |
| G117-24 (V-) - P2-2 (CV-) | Always | Below 1 Ω |
| G117-11 (CA+) or P2-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| G117-12 (V+) or P2-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| G117-23 (CGND) or P2-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| G117-24 (V-) or P2-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Remove the navigation receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G117-23 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G117-11 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the navigation receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
| *a | Component with harness connected
(Navigation Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G117-12 (V+) - G117-24 (V-) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear television camera assembly with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL
Check if the same malfunction recurs when the rear view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG