Home › Engine / Hybrid System › 1GD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD › from 2015.11
RM33J0E _51 Engine / Hybrid System _038424 1GD-FTV INTAKE / EXHAUST _0198022 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 25800 3.REMOVE EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 4.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A359573C02
0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 0.104,2.271 0.417,2.427 0.313,0.156 10 false *b
*a w/ Swirl Control Valve
*b w/o Swirl Control Valve


Remove the engine oil level dipstick.


b.

Disconnect the vacuum hose from the intake manifold.


c.

Remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 23812D 5.DISCONNECT NO. 2 FUEL PIPE

a.
A345097

Remove the bolt and disconnect the No. 2 fuel pipe.


Hide 6.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A345121

Disconnect the diesel throttle body assembly connector and pre-stroke control valve connector.


b.
A345122

Detach the 2 wire harness clamps.


c.

Remove the bolt and wiring harness clamp bracket.


Hide 17118 7.REMOVE MANIFOLD STAY

a.
A345098

Remove the bolt and disconnect the wiring harness clamp bracket from the intake manifold stay.


b.
A345099

Remove the 2 bolts and manifold stay.


Hide 23804D 8.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

a.
A356214C02
0,0 0,0 false
V100136

Union Bolt
V100137

Bolt


Disconnect the No. 4 fuel pipe sub-assembly from the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>PRECAUTION


b.

Remove the bolt from the intake manifold.


c.

Remove the 2 union bolts and 2 gaskets from the supply pump assembly and fuel filter.


Hide 23815D 9.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

a.
A352782C01
0,0 0,0 false
V100135

Union Bolt
V100136

Supply Pump Hollow Screw


Remove the union bolts, supply pump hollow screw and 2 gaskets from the supply pump assembly and fuel filter.


b.

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter.


Hide 23804C 10.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

a.
A345100C01
0.073,0.063 0.385,0.219 0.313,0.156 10 true *a 0.156,2.563 0.469,2.719 0.313,0.156 10 true *b
*a Common Rail Assembly Side
*b Fuel Supply Pump Assembly Side


Remove the 2 bolts, No. 1 injection pipe clamp and No. 2 injection pipe clamp.


b.
A352804E01
0.688,0.781 0.896,0.781 0.896,0.781 1.479,1.667 true 0.323,0.708 0.771,0.979 0.448,0.271 10 true SST

Using SST, loosen the fuel inlet pipe sub-assembly union nut of the common rail assembly side.

NOTICE:

If the No. 1 or No. 2 injection pipe clamp is removed from the inlet pipe sub-assembly, replace the No. 1 or No. 2 injection clamp with a new one.



c.

Using a 19 mm union nut wrench, loosen the inlet pipe sub-assembly union nut of the fuel supply pump assembly side.


Hide 23770 11.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A345101

Slide the clamps and remove the No. 4 fuel hose from the No. 2 nozzle leakage pipe assembly and common rail assembly.


b.

Slide the 2 clamps and remove the No. 5 fuel hose from the No. 1 nozzle leakage pipe assembly and No. 2 nozzle leakage pipe assembly.


c.
A345102

Slide the clamp and disconnect the No. 6 fuel hose from the No. 3 nozzle leakage pipe assembly.


d.

Remove the 2 bolts and No. 2 nozzle leakage pipe assembly.


Hide 25804 12.REMOVE VACUUM CONTROL VALVE SET (for Swirl Control Valve)

A356215

a.

Disconnect the wire harness clamp and vacuum control valve set connector.


b.

Disconnect the 2 vacuum hoses from the vacuum control valve set and vacuum transmitting pipe sub-assembly.


c.

Remove the bolt and vacuum control valve set from the intake manifold.


Hide 17111 13.REMOVE INTAKE MANIFOLD

a.

Remove the bolt and disconnect the wire harness bracket.


b.
A345104

w/o Swirl Control Valve:

Disconnect the vacuum hose from the vacuum transmitting pipe sub-assembly.


c.
A359574C03
0.073,2.542 0.385,2.74 0.313,0.198 10 true *b 0.063,0.052 0.375,0.25 0.313,0.198 10 true *a
*a w/ Swirl Control Valve
*b w/o Swirl Control Valve
V100135

Bolt
V100136

Nut


Remove the 7 bolts, 2 nuts, intake manifold and gasket.