Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.07
RM33J0E _51 Engine / Hybrid System _053774 2TR-FBE ENGINE MECHANICAL _0261411 CYLINDER BLOCK A

2TR-FBE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder block removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of piston or piston ring Inspection after repair Poor idle, engine start, etc. (Click here)

PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A101473

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.15 to 0.35 mm (0.00591 to 0.0138 in.)


Maximum thrust clearance:

0.40 mm (0.0157 in.)


If the thrust clearance is more than the maximum, replace the connecting rod assembly. If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Check that the matchmarks on the connecting rod and cap are aligned to ensure correct reassembly.

HINT:

The matchmarks on the connecting rods and caps are for ensuring correct reassembly.



b.
A101474

Remove the 2 connecting rod cap bolts.


c.

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower connecting rod bearing by wiggling the connecting rod cap right and left.

HINT:

Keep the lower connecting rod bearing installed to the connecting rod cap.



d.

Clean the crank pin and connecting rod bearing.


e.

Check the crank pin and connecting rod bearing for pitting and scratches.


f.
A101475C05
1.479,0.781 0.792,0.26 0.792,0.26 0.615,0.26 true 0.427,0.156 0.625,0.344 0.198,0.188 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


g.
A101476C08
1.313,0.688 0.833,0.135 0.833,0.135 0.708,0.135 true 0.51,0.031 0.708,0.24 0.198,0.208 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing forward.


h.

Install the connecting rod cap.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>CYLINDER BLOCK>REASSEMBLY

NOTICE:

Do not turn the crankshaft.



i.
A101477

Remove the 2 bolts and connecting rod cap (refer to the steps above).


j.
A103430C06
1.448,0.854 0.948,0.302 0.948,0.302 0.823,0.302 true 0.76,3.802 1.667,4.229 1.667,4.229 2.229,3.802 true 0.635,0.198 0.823,0.406 0.188,0.208 10 false *a 1.573,4.271 1.771,4.458 0.198,0.188 10 false *b
*a Plastigage
*b 4, 5 or 6 Mark


Measure the Plastigage at its widest point.

Standard oil clearance:

0.039 to 0.066 mm (0.00154 to 0.00260 in.)


Maximum oil clearance:

0.066 mm (0.00260 in.)


If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, inspect the crankshaft.

If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. The standard thickness of each bearing is indicated by a 4, 5 or 6 mark on its surface.

Standard crankshaft pin diameter:

52.989 to 53.002 mm (2.086 to 2.087 in.)


Standard Connecting Rod Diameter:
Item Specified Condition
Mark 4 56.000 to 56.006 mm (2.20472 to 2.20496 in.)
Mark 5 56.007 to 56.012 mm (2.20500 to 2.20519 in.)
Mark 6 56.013 to 56.018 mm (2.20523 to 2.20543 in.)


Standard Bearing Center Wall Thickness:
Item Specified Condition
Mark 4 1.487 to 1.490 mm (0.05854 to 0.05866 in.)
Mark 5 1.491 to 1.493 mm (0.05870 to 0.05878 in.)
Mark 6 1.494 to 1.496 mm (0.05882 to 0.05890 in.)



k.

Completely remove the Plastigage.


l.

Perform the inspection above for each crank pin.


Hide 3.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
G035191C05
1.438,0.531 1.542,0.177 1.542,0.177 1.729,0.177 false 1.771,0.104 1.979,0.313 0.208,0.208 10 true *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Push the piston, connecting rod assembly and upper connecting rod bearing through the top of the cylinder block.

HINT:
·

Keep the upper connecting rod bearing, connecting rod and cap together.

·

Arrange the piston and connecting rod assemblies in the correct order.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rods and connecting rod caps.

HINT:

Arrange the removed parts in the correct order.



Hide 5.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A101481

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.

Thrust washer thickness:

2.440 to 2.490 mm (0.0961 to 0.0980 in.)



Hide 13411 6.REMOVE CRANKSHAFT

a.
A302861N02
2.948,1.594 3.104,1.792 0.156,0.198 10 true 1 2.969,0.271 3.125,0.469 0.156,0.198 10 true 2 0.458,1.615 0.615,1.813 0.156,0.198 10 true 3 0.479,0.24 0.635,0.438 0.156,0.198 10 true 4 2.302,1.604 2.458,1.802 0.156,0.198 10 true 5 2.323,0.25 2.479,0.448 0.156,0.198 10 true 6 1.063,1.573 1.219,1.813 0.156,0.24 10 true 7 1.688,1.573 1.844,1.792 0.156,0.219 10 true 9 1.063,0.229 1.198,0.438 0.135,0.208 10 true 8 1.656,0.219 1.917,0.427 0.26,0.208 10 true 10

Uniformly loosen the 10 bearing cap bolts in several steps in the sequence shown in the illustration.


b.

Remove the 10 bearing cap bolts, 5 crankshaft bearing caps, 5 lower crankshaft bearings and 2 lower crankshaft thrust washers.

HINT:
·

Keep the lower crankshaft bearings and crankshaft bearing caps together.

·

Arrange the thrust washers in the correct order.




c.

Lift out the crankshaft to remove it.


d.
G037374

Remove the upper thrust washers from the cylinder block.

HINT:

Arrange the crankshaft bearing caps, crankshaft bearings and thrust washers in the correct order.



Hide 11711 7.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings from the cylinder block and bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 8.REMOVE PISTON RING SET

a.
A337671

Using a piston ring expander, remove the 2 compression rings.


b.

Remove the oil ring expander and 2 oil ring side rails by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 9.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.

Check the fitting condition between the piston and piston pin.

i.

Try to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston and pin as a set.



b.

Disconnect the connecting rod from the piston.

i.
G035729C13
2.281,1.521 2.552,1.698 2.552,1.698 2.646,1.698 true 2.688,1.615 2.875,1.781 0.188,0.167 10 false *1
*1 Snap Ring


Using a screwdriver, pry off the snap rings from the piston.


ii.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

CAUTION:

Be sure to wear protective gloves.



iii.
G036556

Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the pistons, piston pins, snap rings, connecting rods and connecting rod bearings in the correct order.





Hide 13101 10.CLEAN PISTON WITH PIN SUB-ASSEMBLY

a.

Using a gasket scraper, remove the carbon from the piston top.


b.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


c.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 15708 11.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A302862

Using a 5 mm hexagon wrench, remove the 4 No. 1 oil nozzle sub-assemblies.


Hide 12.INSPECT BALANCESHAFT THRUST CLEARANCE

a.
A101517

Using a dial indicator, measure the thrust clearance while moving the balanceshaft back and forth.

Standard thrust clearance:

0.07 to 0.13 mm (0.00276 to 0.00512 in.)


Maximum thrust clearance:

0.20 mm (0.00787 in.)


If the thrust clearance is more than the maximum, replace the balanceshaft thrust washer. If necessary, replace the balanceshaft.


Hide 13621 13.REMOVE NO. 1 BALANCESHAFT

a.
A101518

Remove the bolt.


b.
A101519

Remove the No. 1 balanceshaft from the cylinder block.

NOTICE:

When removing the No. 1 balanceshaft, make sure to support the No. 1 balanceshaft with both hands and avoid scratching the No. 1 balanceshaft bearing on the cylinder block side.



Hide 13632 14.REMOVE NO. 1 BALANCESHAFT DRIVEN GEAR

a.
A101520C07
0.594,0.635 0.417,0.75 0.417,0.75 0.417,0.938 false 0.615,0.177 1,0.177 false 1.094,0.854 1.021,1.26 1.021,1.26 0.875,1.26 false 1.896,0.427 1.958,0.156 1.958,0.156 2.094,0.156 false 0.344,0.99 0.521,1.219 0.177,0.229 10 false *1 0.688,1.156 0.875,1.354 0.188,0.198 10 false *4 2.125,0.073 2.333,0.25 0.208,0.177 10 false *3 1.052,0.083 1.26,0.271 0.208,0.188 10 false *2
*1 No. 1 Balanceshaft Driven Gear
*2 Sliding Key
*3 Balanceshaft Thrust Washer
*4 Balanceshaft Thrust Spacer


Mount the head portion of the No. 1 balanceshaft in a vise.

NOTICE:

Do not damage the No. 1 balanceshaft.



b.

Remove the bolt.


c.

Remove the No. 1 balanceshaft driven gear, sliding key, balanceshaft thrust washer and balanceshaft thrust spacer.


Hide 13622 15.REMOVE NO. 2 BALANCESHAFT

a.
A101521

Remove the 2 bolts.


b.
A101522

Remove the No. 2 balanceshaft from the cylinder block.

NOTICE:

When removing the No. 2 balanceshaft, make sure to support the No. 2 balanceshaft with both hands and avoid scratching the No. 2 balanceshaft bearing on the cylinder block side.



Hide 13633 16.REMOVE NO. 2 BALANCESHAFT DRIVEN GEAR

a.
A101523C07
0.75,0.792 0.542,0.958 0.542,0.958 0.542,1.125 false 1.688,0.458 1.792,0.188 1.792,0.188 1.958,0.188 false 0.479,1.167 0.646,1.344 0.167,0.177 10 false *1 2,0.094 2.198,0.281 0.198,0.188 10 false *2
*1 No. 2 Balanceshaft Driven Gear
*2 No. 2 Balanceshaft Thrust Washer


Mount the head portion of the No. 2 balanceshaft in a vise.

NOTICE:

Do not damage the No. 2 balanceshaft.



b.

Remove the bolt.


c.

Remove the No. 2 balanceshaft driven gear and No. 2 balanceshaft thrust washer.


Hide 11415 17.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A302863

Remove the cylinder block water drain cock sub-assembly from the cylinder block.


b.

Remove the water drain cock plug from the cylinder block water drain cock sub-assembly.


Hide 18.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.