Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.07
RM33J0E _51 Engine / Hybrid System _053774 2TR-FBE ENGINE MECHANICAL _0261411 CYLINDER BLOCK A

2TR-FBE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.

A264838C01
2.344,0.698 2.5,0.333 2.5,0.333 2.688,0.333 true 4.052,0.729 3.75,0.385 3.75,0.385 5.5,0.74 true 2.146,1.719 1.74,2.177 1.74,2.177 2.125,1.521 true 1.802,4.438 2.438,3.302 2.438,3.302 2.604,3.302 true 1.771,0.094 1.979,0.292 0.208,0.198 10 false *a 5.198,0.094 5.396,0.292 0.198,0.198 10 false *b 1.771,3.188 1.969,3.385 0.198,0.198 10 false *c 4.917,2.771 5.104,2.979 0.188,0.208 10 false *d 5.656,3.781 5.854,3.99 0.198,0.208 10 false *e 0.927,6.26 1.125,6.448 0.198,0.188 10 false *f 1.615,6.635 1.823,6.865 0.208,0.229 10 false *g 3.563,6.031 3.771,6.24 0.208,0.208 10 false *h 4.333,6.615 4.531,6.823 0.198,0.208 10 false *i 5.875,6.74 6.063,6.979 0.188,0.24 10 false *j 6.573,6.938 6.771,7.156 0.198,0.219 10 false *k 5.875,7.26 6.094,7.469 0.219,0.208 10 false *l 4.906,4.875 5.135,5.073 0.229,0.198 10 false *d 3.552,7.313 3.74,7.51 0.188,0.198 10 false *d 0.917,7.292 1.125,7.5 0.208,0.208 10 false *d 4.521,5.177 4.677,5.375 0.156,0.198 10 false A 0.521,7.615 0.677,7.813 0.156,0.198 10 false B 3.156,7.604 3.313,7.802 0.156,0.198 10 false C 5.479,7.573 5.635,7.771 0.156,0.198 10 false D 2.75,0.24 2.906,0.438 0.156,0.198 10 false A 1.667,2.198 1.823,2.396 0.156,0.198 10 false B 3.583,0.281 3.74,0.479 0.156,0.198 10 false D 2.656,3.208 2.813,3.406 0.156,0.198 10 false C
*a Front Side *b Lower Side
*c Exhaust Side *d 12 mm (0.472 in.)
*e 81 mm (3.19 in.) *f 25 mm (0.984 in.)
*g 56 mm (2.20 in.) *h 18 mm (0.709 in.)
*i 60 mm (2.36 in.) *j 20 mm (0.787 in.)
*k 35 mm (1.38 in.) *l 13 mm (0.512 in.)



a.

Using an E8 "TORX" socket wrench, install the stud bolts labeled A.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Using an E7 "TORX" socket wrench, install the stud bolts labeled B and labeled D.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Apply adhesive to the hole for the stud bolt labeled C on the cylinder block. Using an E7 "TORX" socket wrench, install the stud bolts labeled C.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

HINT:

When reusing a stud bolt, apply adhesive to the bolt before installing it.


Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A101347C06
1.823,3.792 1.656,4.219 1.656,4.219 1.542,4.219 false 1.75,3.729 1.427,3.49 1.427,3.49 1.323,3.49 false 1.958,3.708 2.26,3.854 2.26,3.854 2.385,3.854 false 1.594,2.823 1.771,3.031 0.177,0.208 10 false *c 2.115,3.281 2.323,3.469 0.208,0.188 10 false *d 1.094,3.396 1.344,3.594 0.25,0.198 10 false 30° 2.448,3.74 2.719,3.927 0.271,0.188 10 false 60° 1.344,4.104 1.542,4.292 0.198,0.188 10 false *a 1.896,3.844 2.115,4.031 0.219,0.188 10 false *b
*a Allowable Range
*b Target Direction
*c Upper Side
*d Front


Install the cylinder block water drain cock sub-assembly as shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.

·

Do not loosen the cylinder block water drain cock sub-assembly to adjust it. If an adjustment is necessary, remove the cylinder block water drain cock sub-assembly and reinstall it.




c.

Install the water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15708 3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 13633 4.INSTALL NO. 2 BALANCESHAFT DRIVEN GEAR

a.

Mount the head portion of the No. 2 balanceshaft in a vise.

NOTICE:

Do not damage the balanceshaft.



b.

Install the No. 2 balanceshaft thrust washer and No. 2 balanceshaft driven gear.


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13622 5.INSTALL NO. 2 BALANCESHAFT

a.

Install the No. 2 balanceshaft to the cylinder block.

NOTICE:

When installing the No. 2 balanceshaft, make sure to support the No. 2 balanceshaft with both hands and avoid scratching the No. 2 balanceshaft bearing on the cylinder block side.



b.

Install the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13632 6.INSTALL NO. 1 BALANCESHAFT DRIVEN GEAR

a.

Mount the head portion of the No. 1 balanceshaft in a vise.

NOTICE:

Do not damage the No. 1 balanceshaft.



b.

Install the balanceshaft thrust spacer, balanceshaft thrust washer, sliding key and No. 1 balanceshaft driven gear.


c.

Install the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 13621 7.INSTALL NO. 1 BALANCESHAFT

a.

Install the No. 1 balanceshaft to the cylinder block.

NOTICE:

When installing the No. 1 balanceshaft, make sure to support the No. 1 balanceshaft with both hands and avoid scratching the No. 1 balanceshaft bearing on the cylinder block side.



b.

Install the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 13101 8.INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the piston sub-assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Assemble the piston and connecting rod.

i.
A103205C01
2.458,1.531 2.813,1.375 2.813,1.375 2.979,1.375 true 3.01,1.26 3.219,1.479 0.208,0.219 10 false *a
*a Service Hole Cutout Portion


Using a screwdriver, install a new snap ring at one end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



ii.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

CAUTION:

Be sure to wear protective gloves.



iii.

Coat the piston pin with engine oil.


iv.
A337672C01
1.271,0.448 2.083,0.448 true 1.5,1.688 1.677,1.688 1.677,1.688 2.146,1.844 true 1.073,0.333 1.26,0.542 0.188,0.208 10 false *a 1.313,1.583 1.5,1.792 0.188,0.208 10 false *a
*a Front Mark


Align the front marks of the piston and connecting rod and push in the piston pin with your thumb.

HINT:

The piston and pin are a matched set.



v.
A101515C01
2.469,1.51 2.656,1.302 2.656,1.302 2.854,1.302 true 2.896,1.219 3.104,1.396 0.208,0.177 10 false *a
*a Service Hole Cutout Portion


Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.



vi.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.



Hide 13011 9.INSTALL PISTON RING SET

HINT:

Perform "Inspection After Repairs" after replacing the piston ring.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A164414C15
1.969,1.156 2.458,1.156 false 1.99,1.385 2.208,1.646 2.208,1.646 2.458,1.646 false 1.99,0.917 2.198,0.604 2.198,0.604 2.448,0.604 false 2.49,0.51 2.708,0.708 0.219,0.198 10 false *1 2.5,1.063 2.698,1.26 0.198,0.198 10 false *2 2.5,1.552 2.688,1.74 0.188,0.188 10 false *3
*1 Upper Oil Ring Side Rail
*2 Oil Ring Expander
*3 Lower Oil Ring Side Rail


Install the oil ring expander and 2 oil ring side rails by hand.


b.
A337695C01
1.51,2.042 1.667,2.042 1.667,2.042 1.792,2.323 true 0.604,3.135 0.76,3.135 0.76,3.135 0.99,2.896 false 0.406,3.042 0.604,3.229 0.198,0.188 10 false *1 1.302,1.938 1.5,2.125 0.198,0.188 10 false *a
*1 No. 2 Compression Ring
*a Code Mark (2R)
V100135

Upward


Using a piston ring expander, install the 2 compression rings with the code mark as shown in the illustration.

HINT:
·

The No. 1 compression ring is reversible.

·

Install the No. 2 compression ring with the code mark (2R) facing upward.




c.
A337675C01
0.75,0.896 0.927,0.896 0.927,0.896 1.271,1.031 true 0.073,0.104 0.49,0.292 0.417,0.188 10 false *1, *3 3.052,1.771 3.24,1.979 0.188,0.208 10 false *2 0.323,1.875 0.542,2.083 0.219,0.208 10 false *4 2.969,0.115 3.167,0.302 0.198,0.188 10 false *5 0.552,0.781 0.74,0.979 0.188,0.198 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the compression ring ends.



Hide 11711 10.INSTALL CRANKSHAFT BEARING

NOTICE:

Do not apply engine oil to the contact area or backside of the crankshaft bearing.


HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.


a.

Clean the main journal and both surfaces of the crankshaft bearing.


b.
A302881C04
1.271,2.927 0.656,2.417 0.656,2.417 2.188,2.906 true 0.479,2.302 0.677,2.521 0.198,0.219 10 false *c 1.281,3.979 1.479,4.167 0.198,0.188 10 false *a 2.125,3.979 2.333,4.177 0.208,0.198 10 false *b
*a CORRECT
*b INCORRECT
*c Oil Groove


Install the upper crankshaft bearing.

i.

Install the upper crankshaft bearing to the cylinder block as shown in the illustration.

Reference (Difference in Dimension of Cylinder Block and Bearing):
Item Specified Condition
# 1, 5 journal 3.75 mm (0.1476 in.)
# 3 journal 1.75 mm (0.0689 in.)
# 2, 4 journal 2.75 mm (0.1083 in.)


NOTICE:
·

Do not apply engine oil to the upper crankshaft bearings or their contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.





c.
A101501C06
0.938,0.552 1.083,0.552 1.083,0.552 1.26,1.031 true 1.021,1.833 0.844,1.833 0.844,1.833 0.594,1.458 false 2.74,0.438 2.99,0.708 0.25,0.271 10 false (A) 2.75,1.708 3,1.979 0.25,0.271 10 false (B) 0.75,0.448 0.927,0.604 0.177,0.156 10 false *1 1.083,1.75 1.26,1.906 0.177,0.156 10 false *2
*1 Lower Crankshaft Bearing
*2 Crankshaft Bearing Cap


Install the lower crankshaft bearing.

i.

Install the lower crankshaft bearing to the crankshaft bearing cap.


ii.

Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.

Dimension (A - B) or (B - A):

0.3 mm (0.0118 in.) or less


Reference (Dimension of (A) or (B)):
Item Specified Condition
# 1, 5 journal 3.75 mm (0.1476 in.)
# 3 journal 1.75 mm (0.0689 in.)
# 2, 4 journal 2.75 mm (0.1083 in.)


NOTICE:

Do not apply engine oil to the crankshaft bearings or their contact surfaces.




d.

With the upper crankshaft bearing and lower crankshaft bearing installed, use a plastic-faced hammer to install the crankshaft bearing caps to the cylinder block.

NOTICE:

Make sure that the crankshaft bearing caps are installed in the correct positions and facing in the correct direction.



e.
A101502C06
2.427,0.385 2.615,0.594 0.188,0.208 10 false *a
*a Misalignment


Using a vernier caliper, measure the amount of misalignment between the upper crankshaft bearing and lower crankshaft bearing as shown in the illustration.

Standard misalignment:

0.9 mm (0.0354 in.) or less



f.

Remove the crankshaft bearing cap.


g.

Apply engine oil to the upper crankshaft thrust washers.


h.
A101503C05
1.333,2.51 0.854,3.083 0.854,3.083 1.688,2.781 true 0.656,3.021 0.885,3.208 0.229,0.188 10 false *a
*a Oil Groove


Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.

NOTICE:

Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged.



i.
A101504C08
0.823,1.052 0.76,0.781 0.76,0.781 0.688,0.781 false 2.417,0.323 2.688,0.323 false 0.708,1.125 0.708,1.625 true 1.083,1.542 0.719,1.542 true 0.635,1.656 0.833,1.854 0.198,0.198 10 false *b 0.479,0.667 0.677,0.854 0.198,0.188 10 false *a 2.729,0.229 2.927,0.417 0.198,0.188 10 false *a
*a Claw
*b Oil Groove


Install the 2 lower crankshaft thrust washers to the No. 3 crankshaft bearing cap with the grooves facing outward.

NOTICE:

Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged. The lower crankshaft thrust washers have a claw as shown in the illustration.



j.

Apply engine oil to the lower crankshaft bearing.


Hide 13411 11.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper crankshaft bearing, and then place the crankshaft on the cylinder block.


b.
A101506

Install the 5 crankshaft bearing caps to their proper locations.


c.

Install the crankshaft bearing cap bolts.

i.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


ii.

Temporarily install the crankshaft bearing cap bolts.

HINT:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



iii.
A302882N02
1.698,0.292 1.875,0.458 0.177,0.167 10 true 1 1.708,1.594 1.865,1.792 0.156,0.198 10 true 2 1.073,0.292 1.24,0.448 0.167,0.156 10 true 3 1.083,1.583 1.24,1.781 0.156,0.198 10 true 4 2.333,0.302 2.49,0.5 0.156,0.198 10 true 5 2.333,1.594 2.49,1.792 0.156,0.198 10 true 6 0.479,0.302 0.646,0.479 0.167,0.177 10 true 7 0.458,1.594 0.615,1.792 0.156,0.198 10 true 8 2.969,0.313 3.156,0.49 0.188,0.177 10 true 9 2.938,1.583 3.135,1.781 0.198,0.198 10 true 10

Step 1:

Uniformly tighten the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

If any of the crankshaft bearing cap bolts does not meet the torque specification, replace the crankshaft bearing cap bolt.


iv.

Mark the front of the crankshaft bearing cap bolts with paint.


v.

Step 2:

Tighten the crankshaft bearing cap bolts 90° in the sequence shown in step 1.


vi.

Check that the paint marks are now at a 90° angle to the front.



d.

Check that the crankshaft turns smoothly.


Hide 12.INSPECT CRANKSHAFT THRUST CLEARANCE

Hide 13041 13.INSTALL CONNECTING ROD BEARING

a.
A101528C07
2.677,0.833 2.521,0.542 2.521,0.542 2.448,0.542 true 2.281,0.427 2.469,0.625 0.188,0.198 10 false *a
*a Claw


Align the connecting rod bearing claw with the groove of the connecting rod or connecting rod cap.


b.

Install the bearings in the connecting rod and connecting rod cap.

NOTICE:

Clean the backside of the bearing and the bearing surface of the connecting rod.



Hide 14.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.


b.
A337675C01
0.75,0.896 0.927,0.896 0.927,0.896 1.271,1.031 true 0.073,0.104 0.49,0.292 0.417,0.188 10 false *1, *3 3.052,1.771 3.24,1.979 0.188,0.208 10 false *2 0.323,1.875 0.542,2.083 0.219,0.208 10 false *4 2.969,0.115 3.167,0.302 0.198,0.188 10 false *5 0.552,0.781 0.74,0.979 0.188,0.198 10 false *a
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Oil Ring Expander
*4 Upper Oil Ring Side Rail
*5 Lower Oil Ring Side Rail
*a Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.

NOTICE:

Do not align the compression ring ends.



c.
A337670C01
0.646,0.708 1,0.25 1,0.25 1.188,0.25 true 0.125,1.479 0.302,1.677 0.177,0.198 10 false *a 1.219,0.146 1.406,0.344 0.188,0.198 10 false *b
*a Front
*b Front Mark


Using a piston ring compressor, push the numbered piston and connecting rod assembly into the correct cylinder with the front mark of the piston facing forward.


d.

Match the numbered connecting rod cap with the correct connecting rod.


e.
A101476C09
1.313,0.688 0.833,0.135 0.833,0.135 0.708,0.135 true 0.5,0.021 0.719,0.219 0.219,0.198 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing forward.


f.

Install the connecting rod cap bolts.

HINT:

The connecting rod cap bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


ii.
A101477

Step 1:

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


iii.

Mark the front of each connecting rod cap bolt with paint.


iv.

Step 2:

Tighten the connecting rod cap bolts 90° as shown.


v.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.


Hide 15.INSPECT CONNECTING ROD THRUST CLEARANCE