Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.07
RM33J0E _58 Vehicle Interior _038499 METER / GAUGE / DISPLAY _0189806 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B1500 Fuel Sender Open Detected Both conditions are met:
·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.

·

Average input signal of fuel sender gauge is 4.85 V or more or 0.15 V or less.


·

Fuel sender gauge assembly

·

Fuel suction with pump and gauge tube assembly*1

·

Fuel tank vent tube assembly*2

·

Harness or connector

·

Combination meter assembly



*1: for Gasoline Engine

*2: for Diesel Engine


WIRING DIAGRAM

E316680E21
5,2.969 6.885,3.354 1.885,0.385 10 false G9 5,3.125 6.885,3.51 1.885,0.385 10 false Combination Meter Assembly 0.417,2.969 2.906,3.406 2.49,0.438 10 false O6 0.427,3.156 3.865,3.448 3.438,0.292 10 false Fuel Suction with Pump and Gauge Tube Assembly*1 0.615,2.25 3.104,2.688 2.49,0.438 10 false Fuel Sender Gauge Assembly 3.25,0.958 3.875,1.375 0.625,0.417 10 false FV 4.979,0.979 5.604,1.396 0.625,0.417 10 false FV 3.594,0.927 4.219,1.344 0.625,0.417 10 false 1 4.677,0.958 5.302,1.375 0.625,0.417 10 false 24 4.698,1.365 5.323,1.781 0.625,0.417 10 false 25 4.667,1.781 5.292,2.198 0.625,0.417 10 false 26 4.969,1.813 5.594,2.229 0.625,0.417 10 false FE&B 4.979,1.385 5.604,1.802 0.625,0.417 10 false FR 3.25,1.365 3.875,1.781 0.625,0.417 10 false FR 3.25,1.771 3.875,2.188 0.625,0.417 10 false FE 3.594,1.354 4.219,1.771 0.625,0.417 10 false 3 3.594,1.771 4.219,2.188 0.625,0.417 10 false 2 2.469,1.385 3.094,1.802 0.625,0.417 10 false 1 2.469,0.969 3.094,1.385 0.625,0.417 11 false 3 2.5,1.802 3.125,2.219 0.625,0.417 10 false 2 5.688,0.844 6.313,1.26 0.625,0.417 10 false 5 V 6.177,1.615 6.802,2.031 0.625,0.417 10 false CPU 0.406,3.5 3.844,3.792 3.438,0.292 10 false Fuel Tank Vent Tube Assembly*2 0.302,4.104 2.104,4.375 1.802,0.271 10 false *1: for Gasoline Engine 0.313,4.427 3.75,4.719 3.438,0.292 10 false *2: for Diesel Engine

CAUTION / NOTICE / HINT

CAUTION:

Be careful of flames.


NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0, Max.: 127.5 Current fuel level displayed Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39
OK:

Fuel amount value displayed on the GTS is almost the same as the needle indication.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the O6 fuel suction tube with pump and gauge assembly*1 or fuel tank vent tube assembly*2 connector.

*1: for Gasoline Engine

*2: for Diesel Engine



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-25 (FR) - O6-3 (FR) Always Below 1 Ω
G9-24 (FV) - O6-1 (FV) Always Below 1 Ω
G9-26 (FE&B) - O6-2 (FE) Always Below 1 Ω
G9-25 (FR) or O6-3 (FR) - Body ground Always 10 kΩ or higher
G9-24 (FV) or O6-1 (FV) - Body ground Always 10 kΩ or higher
G9-26 (FE&B) or O6-2 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER ASSEMBLY
a.
E317793C03
1.49,0.188 1.958,0.417 0.469,0.229 2.906,1.667 2.729,1.667 2.729,1.667 2.281,1.302 true 2.51,1.99 2.333,1.99 2.333,1.99 2.104,1.292 true 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.625,0.208 1.938,0.365 0.313,0.156 10 false G9 2.979,1.552 3.292,1.708 0.313,0.156 10 false FV 2.552,1.875 3.052,2.052 0.5,0.177 10 false FE&B
*a Component with harness connected
(Combination Meter Assembly)


Remove the combination meter assembly with its connectors still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G9-24 (FV) - Body ground Always 4.5 to 5.2 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-26 (FE&B) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FUEL SENDER GAUGE ASSEMBLY

A

5.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

6.INSPECT FUEL TANK VENT TUBE ASSEMBLY

C

5.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E322191C01
0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.115,1.885 0.427,2.042 0.313,0.156 10 false *b 1.625,0.417 1.938,0.573 0.313,0.156 10 false *c 1.625,1.802 1.938,1.958 0.313,0.156 10 false *d
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Remove the fuel suction with pump and gauge tube assembly.

for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2TR-FBE: Click hereEngine / Hybrid System>2TR-FBE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-1 Always 10 kΩ or higher
A-2 - B-3 Always 10 kΩ or higher
A-3 - B-3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

6.INSPECT FUEL TANK VENT TUBE ASSEMBLY
a.
E322191C01
0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.115,1.885 0.427,2.042 0.313,0.156 10 false *b 1.625,0.417 1.938,0.573 0.313,0.156 10 false *c 1.625,1.802 1.938,1.958 0.313,0.156 10 false *d
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Remove the fuel tank vent tube assembly.

for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL

for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - B-1 Always 10 kΩ or higher
A-2 - B-3 Always 10 kΩ or higher
A-3 - B-3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG