Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.07
RM33J0E _51 Engine / Hybrid System _053773 2TR-FBE ENGINE CONTROL _0264980 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E35
4.375,1.073 6.198,1.25 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,1.927 6.365,2.344 1.01,0.417 10 false Microprocessor 0.917,1.49 2.667,1.719 1.75,0.229 10 false from EFI-MAIN NO. 1 Relay 1.51,1.135 3.188,1.302 1.677,0.167 10 false from EFI-B Fuse 3.75,1 4.24,1.219 0.49,0.219 10 false BATT 0.313,1.948 2.635,2.458 2.323,0.51 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.302,2.969 2.552,3.396 2.25,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature, etc. 4.073,2.823 4.333,3.031 0.26,0.208 10 false R 3.698,1.354 4.625,1.552 0.927,0.198 10 false +B, +B2 3.708,2.271 4,2.5 0.292,0.229 10 false VC 4.885,0.354 5.333,0.583 0.448,0.229 10 false ECM

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit


·

VC Power Source Circuit

A348509E06
5.625,0.646 6.24,0.844 0.615,0.198 10 false VCV1 5.615,1.156 6.229,1.354 0.615,0.198 10 false VV1+ 5.615,1.469 6.229,1.667 0.615,0.198 10 false VV1- 5.625,2.271 6.24,2.469 0.615,0.198 10 false VCE1 5.615,2.771 6.229,2.969 0.615,0.198 10 false EV1+ 5.635,3.115 6.25,3.313 0.615,0.198 10 false EV1- 5.885,7.531 6.344,7.729 0.458,0.198 10 false ECM 0.26,0.948 1.875,1.677 1.615,0.729 10 false Camshaft Position Sensor (for Intake Side) 0.302,2.563 1.958,3.063 1.656,0.5 10 false Camshaft Position Sensor (for Exhaust Side) 0.292,4.229 3.198,4.427 2.906,0.198 10 false Air Pressure Sensor 2.552,4 2.865,4.198 0.313,0.198 10 false VC 2.583,4.802 2.896,5 0.313,0.198 10 false E2 2.542,4.396 3,4.594 0.458,0.198 10 false AIP 2.5,2.365 2.958,2.563 0.458,0.198 10 false VC2 2.438,2.74 3.052,2.938 0.615,0.198 10 false VVE+ 2.406,3.177 3.021,3.375 0.615,0.198 10 false VVE- 2.552,0.74 2.865,0.938 0.313,0.198 10 false VC 2.427,1.125 3.042,1.323 0.615,0.198 10 false VVI+ 2.448,1.542 3.063,1.74 0.615,0.198 10 false VVI- 5.625,5.615 6.24,5.813 0.615,0.198 10 false VCVG 5.646,6.031 6.104,6.229 0.458,0.198 10 false E2G 5.635,7.01 6.094,7.208 0.458,0.198 10 false THA 5.615,6.531 5.927,6.729 0.313,0.198 10 false VG 0.271,6.052 2,6.458 1.729,0.406 10 false Intake Mass Air Flow Meter Sub-assembly 2.604,5.708 2.917,5.906 0.313,0.198 10 false 5V 2.583,6.531 2.896,6.729 0.313,0.198 10 false FG 2.5,7.01 2.958,7.208 0.458,0.198 10 false THA 2.49,6.104 2.948,6.302 0.458,0.198 10 false E2G 2.885,5.615 3.042,5.813 0.156,0.198 10 false 3 2.885,6.427 3.042,6.625 0.156,0.198 10 false 1 2.906,6.896 3.063,7.094 0.156,0.198 10 false 4 2.896,6.042 3.052,6.24 0.156,0.198 10 false 2 5.271,5.708 5.729,5.906 0.458,0.198 10 false C53 5.281,6.115 5.74,6.313 0.458,0.198 10 false C53 5.292,6.542 5.75,6.74 0.458,0.198 10 false C53 5.281,7.01 5.74,7.208 0.458,0.198 10 false C53 5.354,5.531 5.667,5.729 0.313,0.198 10 false 33 5.354,5.948 5.667,6.146 0.313,0.198 10 false 32 5.375,6.365 5.688,6.563 0.313,0.198 10 false 24 5.375,6.833 5.688,7.031 0.313,0.198 10 false 23 5.625,3.896 6.24,4.094 0.615,0.198 10 false VCAI 5.271,3.99 5.729,4.188 0.458,0.198 10 false C52 5.365,3.813 5.677,4.01 0.313,0.198 10 false 20 5.615,4.729 6.229,4.927 0.615,0.198 10 false EAIP 5.281,4.396 5.74,4.594 0.458,0.198 10 false C52 5.375,4.656 5.688,4.854 0.313,0.198 10 false 25 5.625,4.406 6.083,4.604 0.458,0.198 10 false AIP 5.281,4.823 5.74,5.021 0.458,0.198 10 false C52 5.375,4.229 5.688,4.427 0.313,0.198 10 false 26 5.271,2.365 5.729,2.563 0.458,0.198 10 false C52 5.354,2.177 5.667,2.375 0.313,0.198 10 false 31 5.281,2.781 5.74,2.979 0.458,0.198 10 false C52 5.354,2.604 5.667,2.802 0.313,0.198 10 false 24 5.281,3.198 5.74,3.396 0.458,0.198 10 false C52 5.354,3.031 5.667,3.229 0.313,0.198 10 false 32 5.292,0.74 5.75,0.938 0.458,0.198 10 false C52 5.365,0.552 5.677,0.75 0.313,0.198 10 false 21 5.365,0.979 5.677,1.177 0.313,0.198 10 false 23 5.281,1.156 5.74,1.354 0.458,0.198 10 false C52 5.281,1.573 5.74,1.771 0.458,0.198 10 false C52 5.375,1.406 5.688,1.604 0.313,0.198 10 false 22 0.25,0.802 0.708,1 0.458,0.198 10 false C65 0.26,2.417 0.719,2.615 0.458,0.198 10 false C64 0.271,4.063 0.583,4.26 0.313,0.198 10 false C70 0.26,5.875 0.719,6.073 0.458,0.198 10 false A39 2.875,0.615 3.031,0.813 0.156,0.198 10 false 3 2.885,1.01 3.042,1.208 0.156,0.198 10 false 1 2.885,1.458 3.042,1.656 0.156,0.198 10 false 2 2.885,2.24 3.042,2.438 0.156,0.198 10 false 3 2.885,2.656 3.042,2.854 0.156,0.198 10 false 1 2.896,3.083 3.052,3.281 0.156,0.198 10 false 2 2.885,3.844 3.042,4.042 0.156,0.198 10 false 3 2.885,4.729 3.042,4.927 0.156,0.198 10 false 1 2.885,4.313 3.042,4.51 0.156,0.198 10 false 2

A255263E37
6.125,5.146 6.469,5.302 0.344,0.156 10 false ECM 5.354,0.865 5.781,1.135 0.427,0.271 10 false 29 5.667,0.927 6.188,1.229 0.521,0.302 10 false VCTA 5.333,1.021 5.76,1.365 0.427,0.344 10 false C52 5.354,1.229 5.75,1.51 0.396,0.281 10 false 30 5.333,1.385 5.698,1.646 0.365,0.26 10 false C52 5.354,1.604 5.615,1.76 0.26,0.156 10 false 18 5.333,1.75 5.688,1.938 0.354,0.188 10 false C52 5.333,2.115 5.76,2.313 0.427,0.198 10 false C52 5.354,1.969 5.604,2.125 0.25,0.156 10 false 28 5.667,1.385 6.052,1.531 0.385,0.146 10 false VTA1 5.667,1.75 6.052,1.896 0.385,0.146 10 false VTA2 5.667,2.031 5.979,2.177 0.313,0.146 10 false ETA 5.385,2.406 5.688,2.688 0.302,0.281 10 false 20 5.323,2.552 5.656,2.771 0.333,0.219 10 false G46 5.323,2.917 5.896,3.198 0.573,0.281 10 false G46 5.313,3.281 5.708,3.49 0.396,0.208 10 false G46 5.313,3.677 5.781,3.917 0.469,0.24 10 false G46 5.323,4.031 5.969,4.313 0.646,0.281 10 false G46 5.313,4.396 5.833,4.74 0.521,0.344 10 false G46 5.385,2.771 5.833,3 0.448,0.229 10 false 22 5.385,3.135 5.719,3.323 0.333,0.188 10 false 26 5.385,3.531 5.771,3.781 0.385,0.25 10 false 28 5.385,3.875 5.74,4.115 0.354,0.24 10 false 27 5.385,4.26 5.688,4.542 0.302,0.281 10 false 29 5.667,2.458 6.073,2.615 0.406,0.156 10 false VCPA 5.667,3.281 5.979,3.438 0.313,0.156 10 false VPA 5.667,3.958 5.979,4.115 0.313,0.156 10 false EPA 5.667,3.667 6.042,3.823 0.375,0.156 10 false VPA2 5.667,4.323 6.115,4.563 0.448,0.24 10 false EPA2 5.667,2.833 6.073,2.99 0.406,0.156 10 false VCP2 0.25,1.167 0.948,1.448 0.698,0.281 10 false C11 0.24,1.354 1.76,1.917 1.521,0.563 10 false Throttle Body with Motor Assembly 2.594,1.021 3.115,1.26 0.521,0.24 10 false VC 2.521,1.375 2.833,1.531 0.313,0.156 10 false VTA 2.448,1.74 2.958,2.052 0.51,0.313 10 false VTA2 2.625,2.104 2.844,2.271 0.219,0.167 10 false E2 2.938,0.927 3.052,1.083 0.115,0.156 10 false 5 2.938,1.292 3.052,1.448 0.115,0.156 10 false 6 2.938,1.656 3.052,1.813 0.115,0.156 10 false 4 2.938,2.021 3.052,2.177 0.115,0.156 10 false 3 0.25,2.688 0.656,2.844 0.406,0.156 10 false A41 0.25,2.865 1.385,3.479 1.135,0.615 10 false Accelerator Pedal Sensor Assembly 2.438,2.552 3,2.792 0.563,0.24 10 false VCPA 2.438,2.927 2.854,3.073 0.417,0.146 10 false VCP2 2.521,3.292 2.896,3.458 0.375,0.167 10 false VPA 2.448,3.667 2.969,3.896 0.521,0.229 10 false VPA2 2.531,4.031 3,4.271 0.469,0.24 10 false EPA 2.448,4.375 3.083,4.646 0.635,0.271 10 false EPA2 2.938,2.458 3.177,2.604 0.24,0.146 10 false 4 2.938,2.833 3.052,2.99 0.115,0.156 10 false 1 2.938,3.188 3.052,3.344 0.115,0.156 10 false 6 2.938,3.594 3.052,3.75 0.115,0.156 10 false 3 2.938,3.948 3.052,4.104 0.115,0.156 10 false 5 2.938,4.313 3.052,4.469 0.115,0.156 10 false 2


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
A352218C14
1.896,0.094 2.385,0.344 0.49,0.25 2.354,0.688 1.677,1.76 true 2.479,0.677 2.667,1.74 true 1.99,0.135 2.448,0.333 0.458,0.198 10 false G46 2.542,1.802 3.313,2 0.771,0.198 10 false 1(+B) 1.469,1.813 1.948,2.042 0.479,0.229 10 false 2(+B2) 0.219,0.531 0.531,0.729 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G46-1(+B) - Body ground Ignition switch ON 11 to 14 V
G46-2(+B2) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

4.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (AIR PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK CONNECTION BETWEEN GTS AND ECM (AIR PRESSURE SENSOR)
a.

Disconnect the air pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY)

B

6.CHECK CONNECTION BETWEEN GTS AND ECM (INTAKE MASS AIR FLOW METER SUB-ASSEMBLY)
a.

Disconnect the intake mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the intake mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR INTAKE SIDE)

B

REPLACE INTAKE MASS AIR FLOW METER SUB-ASSEMBLY

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR INTAKE SIDE)
a.

Disconnect the camshaft position sensor (for intake side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR EXHAUST SIDE)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE SIDE)

8.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR FOR EXHAUST SIDE)
a.

Disconnect the camshaft position sensor (for exhaust side) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK HARNESS AND CONNECTOR

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST SIDE)

9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the air pressure sensor connector.


d.

Disconnect the intake mass air flow meter sub-assembly connector.


e.

Disconnect the camshaft position sensor (for intake side) connector.


f.

Disconnect the camshaft position sensor (for exhaust side) connector.


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C52-29 (VCTA) - Body ground Always 10 kΩ or higher
G46-20 (VCPA) - Body ground Always 10 kΩ or higher
G46-22 (VCP2) - Body ground Always 10 kΩ or higher
C53-33 (VCVG) - Body ground Always 10 kΩ or higher
C52-20 (VCAI) - Body ground Always 10 kΩ or higher
C52-31 (VCE1) - Body ground Always 10 kΩ or higher
C52-21 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR