The sound signals amplified by the navigation receiver assembly are sent to the speakers from the navigation receiver assembly via the speaker circuit.
If there is a short in a speaker circuit, the navigation receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the navigation receiver assembly or speakers.
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 4 Speakers | B |
A
B
*1: for LH Side
*2: for RH Side
Disconnect the G118 and G119 navigation receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the K7*1 and/or J7*2 front No. 2 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-2 (FL+) - K7-4 (TWL+) | Always | Below 1 Ω |
| G118-6 (FL-) - K7-2 (TWL-) | Always | Below 1 Ω |
| K7-3 (+) - K4-1 | Always | Below 1 Ω |
| K7-1 (-) - K4-2 | Always | Below 1 Ω |
| G119-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G119-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G118-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G118-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| G119-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G119-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| K7-3 (+) - Body ground | Always | 10 kΩ or higher |
| K7-1 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-1 (FR+) - J7-4 (TWR+) | Always | Below 1 Ω |
| G118-5 (FR-) - J7-2 (TWR-) | Always | Below 1 Ω |
| J7-3 (+) - J4-1 | Always | Below 1 Ω |
| J7-1 (-) - J4-2 | Always | Below 1 Ω |
| G119-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G119-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G118-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G118-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| G119-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G119-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| J7-3 (+) - Body ground | Always | 10 kΩ or higher |
| J7-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for LH Side
*2: for RH Side
Disconnect the G118 and G119 navigation receiver assembly connectors.
Disconnect the K4*1 and/or J4*2 front No. 1 speaker assembly connector.
Disconnect the M2*1 and/or L2*2 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-2 (FL+) - K4-1 | Always | Below 1 Ω |
| G118-6 (FL-) - K4-2 | Always | Below 1 Ω |
| G119-2 (RL+) - M2-1 | Always | Below 1 Ω |
| G119-6 (RL-) - M2-2 | Always | Below 1 Ω |
| G118-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G118-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| G119-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G119-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G118-1 (FR+) - J4-1 | Always | Below 1 Ω |
| G118-5 (FR-) - J4-2 | Always | Below 1 Ω |
| G119-1 (RR+) - L2-1 | Always | Below 1 Ω |
| G119-3 (RR-) - L2-2 | Always | Below 1 Ω |
| G118-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G118-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| G119-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G119-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly connector.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Smart Cab)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG