The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front wheel alignment adjustment removal /installation are shown below.
1.INSPECT TIRES
2.INSPECT VEHICLE HEIGHT
Before inspecting the wheel alignment, adjust the vehicle height to the specification.
| *A | for Front |
| *B | for Rear |
Press down on the vehicle several times to stabilize the suspension, and measure the vehicle height.
| Vehicle Model | Front A - B | Rear C - D | |
|---|---|---|---|
| GUN156R-STFLHQ | Tire Size 265/65R17
for Steel Wheel |
70 mm (2.76 in.) | 72 mm (2.83 in.) |
| Tire Size 265/65R17
for Aluminum Wheel |
70 mm (2.76 in.) | 71 mm (2.80 in.) | |
| GUN156R-STFSHQ | 70 mm (2.76 in.) | 72 mm (2.83 in.) | |
| GUN156R-STFMHQ | 71 mm (2.80 in.) | 72 mm (2.83 in.) | |
| GUN156R-STTLHQ | Tire Size 265/65R17
for Steel Wheel |
70 mm (2.76 in.) | 72 mm (2.83 in.) |
| Tire Size 265/65R17
for Aluminum Wheel |
70 mm (2.76 in.) | 71 mm (2.80 in.) | |
| GUN156R-STTSHQ | 70 mm (2.76 in.) | 71 mm (2.80 in.) | |
| GUN156R-STTMHQ | 71 mm (2.80 in.) | 72 mm (2.83 in.) | |
Ground clearance of front wheel center
Ground clearance of lower suspension arm No. 2 set bolt center
Ground clearance of rear wheel center
Ground clearance of strut rod set bolt center
If the vehicle height is not as specified, press down on the vehicle several times to stabilize the suspension. Then measure the vehicle height again.
The standard value shown above is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.
3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION
| *a | Gauge |
| *b | Alignment Tester |
Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.
Inspect the camber, caster and steering axis inclination.
| Vehicle Model | Camber Inclination | |
|---|---|---|
| GUN156R-STFLHQ
Right-left error |
Tire Size 265/65R17
for Steel Wheel |
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17
for Aluminum Wheel |
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFSHQ
Right-left error |
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFMHQ
Right-left error |
Tire Size 265/60R18 | 0°16' +/-30' (0.27° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTLHQ
Right-left error |
Tire Size 265/65R17
for Steel Wheel |
0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17
for Aluminum Wheel |
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTSHQ
Right-left error |
0°18' +/-30' (0.30° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTMHQ
Right-left error |
Tire Size 265/60R18 | 0°16' +/-30' (0.27° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 0°17' +/-30' (0.28° +/-0.50°)
30' (0.50°) or less |
|
| Vehicle Model | Caster Inclination | |
|---|---|---|
| GUN156R-STFLHQ
Right-left error |
Tire Size 265/65R17
for Steel Wheel |
2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17
for Aluminum Wheel |
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFSHQ
Right-left error |
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFMHQ
Right-left error |
Tire Size 265/60R18 | 2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 2°37' +/-30' (2.62° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTLHQ
Right-left error |
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTSHQ
Right-left error |
2°36' +/-30' (2.60° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTMHQ
Right-left error |
Tire Size 265/60R18 | 2°38' +/-30' (2.63° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 2°37' +/-30' (2.62° +/-0.50°)
30' (0.50°) or less |
|
| Vehicle Model | Steering Axis Inclination | |
|---|---|---|
| GUN156R-STFLHQ
Right-left error |
Tire Size 265/65R17
for Steel Wheel |
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17
for Aluminum Wheel |
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFSHQ
Right-left error |
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STFMHQ
Right-left error |
Tire Size 265/60R18 | 12°13' +/-30' (12.22° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTLHQ
Right-left error |
Tire Size 265/65R17
for Steel Wheel |
12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17
for Aluminum Wheel |
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTSHQ
Right-left error |
12°11' +/-30' (12.18° +/-0.50°)
30' (0.50°) or less |
|
| GUN156R-STTMHQ
Right-left error |
Tire Size 265/60R18 | 12°13' +/-30' (12.22° +/-0.50°)
30' (0.50°) or less |
| Tire Size 265/65R17 | 12°12' +/-30' (12.20° +/-0.50°)
30' (0.50°) or less |
|
If the camber and caster are not as specified, adjust them.
If the steering axis inclination is not as specified after the camber and caster have been correctly adjusted, check the steering knuckle and front wheel for distortion or looseness.
4.ADJUST CAMBER AND CASTER
After the camber has been adjusted, inspect the toe-in.
Loosen the camber adjusting cam nut and camber adjusting cam bolt.
Turn the No. 1 camber adjusting cam and No. 2 camber adjusting cam in both directions, and adjust the camber and caster to the center value.
The camber and caster should be as close as possible to the center value.
| *1 | No. 1 Camber Adjusting Cam (LH) | *2 | No. 1 Camber Adjusting Cam (RH) |
| *3 | No. 2 Camber Adjusting Cam (LH) | *4 | No. 2 Camber Adjusting Cam (RH) |
| *a | Front of the Vehicle | - | - |
Moving the No. 1 camber adjusting cam to (+) side by one notch changes the caster by approximately +0°07' and the camber by approximately +0°03'.
Moving the No. 2 camber adjusting cam to (+) side by one notch changes the caster by approximately +0°06' and the camber by approximately +0°04'.
Perform adjustments so that the value is as close as possible to the median of the specified range.
Tighten the camber adjusting cam nut and camber adjusting cam bolt.
5.INSPECT TOE-IN
|
Front of the Vehicle |
| Vehicle Model | A + B
C - D |
|
|---|---|---|
| GUN156R-STFLHQ | Tire Size 265/65R17
for Steel Wheel |
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.) |
| Tire Size 265/65R17
for Aluminum Wheel |
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.) |
|
| GUN156R-STFSHQ | A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.) |
|
| GUN156R-STFMHQ | A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.) |
|
| GUN156R-STTLHQ | Tire Size 265/65R17
for Steel Wheel |
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.) |
| Tire Size 265/65R17
for Aluminum Wheel |
A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.) |
|
| GUN156R-STTSHQ | A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.7 +/-1.0 mm (0.07 +/-0.04 in.) |
|
| GUN156R-STTMHQ | A + B: 0°07' +/-5' (0.12° +/-0.08°)
C - D: 1.6 +/-1.0 mm (0.06 +/-0.04 in.) |
|
If the toe-in is not as specified, adjust it at the rack ends.
6.ADJUST TOE-IN
Loosen the tie rod end lock nuts.
Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.
| *a | Thread Length |
Adjust the tie rod end sub-assembly so that thread length is within the specified ranges.
17 mm (0.669 in.) or less
Perform adjustments so that the value is as close as possible to the median of the specified range.
| *a | Torque Wrench Fulcrum Length |
| *b | Turn |
| *c | Hold |
Tighten the tie rod end lock nuts.
Make sure that the boots are not twisted.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When using SST (fulcrum length of 135.5 mm (5.335 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 44.7 N*m (456 kgf*cm, 33 ft.*lbf)
7.INSPECT WHEEL ANGLE
| *a | Inside |
| *b | Outside |
|
Front of the Vehicle |
Turn the steering wheel to the left and right full lock positions, and measure the wheel angle.
| Inside Wheel Angle | Outside Wheel Angle (Reference) |
|---|---|
| 35°00' (33°00' to 36°00')(35.00° (33.00° to 36.00°)) | 31°42' (31.70°) |
If the angles are not as specified, check and adjust the right and left rack end lengths.
8.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
9. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION