Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM
RM3270E _53 Suspension _041688 FRONT SUSPENSION _0195318 FRONT LOWER SUSPENSION ARM A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48304 1.INSTALL FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY

a.
C322877C01
1.146,1.042 1.479,1.042 false 1.521,0.958 1.979,1.156 0.458,0.198 10 false SST 1.135,1.792 1.594,1.99 0.458,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using SST, install the front spring bumper to the vehicle.

SST
09922-10010  

Torque:
Specified tightening torque : 31 N*m (316 kgf*cm, 23 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 69.68 mm (2.7433 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 25.2 N*m (257 kgf*cm, 19 ft.*lbf)




Hide 43340A 2.INSTALL FRONT LOWER BALL JOINT ASSEMBLY LH

a.
C237856N05
1.594,0.177 2.115,0.177 2.115,0.177 2.625,0.844 true 2.448,2.323 2.75,2.323 false 2.75,2.323 2.906,1.938 false 1.208,0.115 1.615,0.323 0.406,0.208 10 false SST 2.031,2.24 2.438,2.448 0.406,0.208 10 false SST

Using SST and press, press in a new front lower ball joint assembly LH.

SST
09226-10010  
09631-32020  


b.

Install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 48655E 3.INSTALL FRONT NO. 2 LOWER ARM BUSH

a.
C322848C01
0.417,2.417 0.583,2.417 0.583,2.417 0.75,2.25 true 0.625,1.625 0.438,1.385 0.438,1.385 0.656,1.375 false 0.469,3.719 1.052,3.479 1.052,3.479 0.49,4.188 true 0.135,1.302 0.594,1.5 0.458,0.198 10 false SST 0.125,2.313 0.583,2.51 0.458,0.198 10 false SST 1.104,3.385 1.563,3.583 0.458,0.198 10 false *a
*a Bush Positioning Protrusion


Using SST and a press, install a new front No. 2 lower arm bush.

SST
09502-12010  
09513-36040  
09710-14013  (09710-00021)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 48654F 4.INSTALL FRONT NO. 1 LOWER ARM BUSH

a.
C322849C01
0.896,1.281 0.688,1.198 0.688,1.198 0.896,1.073 false 0.708,2.563 0.885,2.563 0.885,2.563 1.042,1.906 true 2.781,3.844 2.427,4.323 2.427,4.323 3.25,3.823 true 0.354,1.115 0.813,1.313 0.458,0.198 10 false SST 0.406,2.49 0.865,2.688 0.458,0.198 10 false SST 2.219,4.26 2.677,4.458 0.458,0.198 10 false *a
*a Bush Positioning Protrusion


Using SST and a press, press in a new front No. 1 lower arm bush.

SST
09710-14013  (09710-00021)
09710-20011  (09710-06041)
09950-60010  (09951-00650)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 48626 5.INSTALL FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Install the front lower ball joint attachment LH with the nut and a new cotter pin.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 48069 6.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

C322843C01
0.917,0.74 2.792,0.542 2.792,0.542 2.615,0.781 true 0.99,1.375 1.042,1.51 1.042,1.51 1.188,1.51 true 2.49,1.344 2.542,1.479 2.542,1.479 2.688,1.479 true 2.844,0.427 3.156,0.625 0.313,0.198 10 true *a 2.729,1.406 3.042,1.604 0.313,0.198 10 true *2 1.208,1.427 1.521,1.625 0.313,0.198 10 true *1
*1 No. 1 Camber Adjusting Cam
*2 No. 2 Camber Adjusting Cam
*a Matchmark


a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH, and No. 1 and No. 2 camber adjusting cams with the No. 1 and No. 2 camber adjusting cam assemblies and 2 nuts.


b.

Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.


c.

Install the front lower ball joint attachment LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Temporarily install the front shock absorber with coil spring with the bolt and nut.


Hide 8.INSTALL FRONT WHEEL

Hide 48069 10.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Tighten the 2 nuts.

Torque:
185 N*m (1886 kgf*cm, 136 ft.*lbf)


Hide 11.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 4866A 12.INSTALL FRONT LOWER ARM SHAFT BOOT PROTECTOR LH (w/ Drive Shaft Boot Protector)

a.

Install the front lower arm shaft boot protector LH with the 2 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 51442 13.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51410 14.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 15.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 16.PERFORM INITIALIZATION (w/ Automatic Headlight Beam Level Control System)

Hide 17.INSPECT AUTOMATIC LIGHT CONTROL SYSTEM (w/ Automatic Headlight Beam Level Control System)

Hide 18.INSPECT HEADLIGHT AIMING (w/ Automatic Headlight Beam Level Control System)