Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0195472 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 Short in GPS Antenna Navigation antenna error
·

Navigation antenna assembly

·

No. 2 navigation antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly


B15C1 Open in GPS Antenna Error of the power source to the navigation antenna
·

Navigation antenna assembly

·

No. 2 navigation antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E317089E06
2.156,0.417 2.313,0.615 0.156,0.198 10 false A 2.156,1.125 2.313,1.323 0.156,0.198 10 false A 3.865,0.427 4.021,0.625 0.156,0.198 10 false B 3.854,1.125 4.01,1.323 0.156,0.198 10 false B 5.604,0.427 5.76,0.625 0.156,0.198 10 false C 5.594,1.125 5.75,1.323 0.156,0.198 10 false C 2.167,0.219 2.323,0.417 0.156,0.198 10 false 3 2.115,0.917 2.396,1.115 0.281,0.198 10 false 3a 3.865,0.219 4.021,0.417 0.156,0.198 10 false 3 3.833,0.906 4.115,1.104 0.281,0.198 10 false 3a 5.594,0.208 5.75,0.406 0.156,0.198 10 false 1 5.583,0.917 5.865,1.115 0.281,0.198 10 false 1a 0.802,1.719 2.052,2.063 1.25,0.344 10 false Navigation Antenna Assembly 2.313,1.729 3.865,2.094 1.552,0.365 10 false No. 2 Navigation Antenna Cord Sub-assembly 4.354,1.74 5.271,2.094 0.917,0.354 10 false Antenna Cord Sub-assembly 5.813,1.917 7,2.375 1.188,0.458 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NAVIGATION ANTENNA ASSEMBLY
2.INSPECT NAVIGATION ANTENNA ASSEMBLY
a.
E317090C01
1.563,1.146 1.635,0.833 true 1.469,1.156 1.656,1.313 0.188,0.156 10 false 3a 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Remove the navigation antenna assembly.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 NAVIGATION ANTENNA CORD SUB-ASSEMBLY

NG

3.CHECK NO. 2 NAVIGATION ANTENNA CORD SUB-ASSEMBLY
a.
E317091C01
1.5,0.135 1.833,0.375 0.333,0.24 1.51,1.906 1.844,2.146 0.333,0.24 1.958,1.688 1.792,0.927 true 2.083,3.135 2.021,2.865 true 0.302,0.229 0.479,0.385 0.177,0.156 10 false *a 0.354,2.271 0.531,2.427 0.177,0.156 10 false *b 1.917,1.708 2.115,1.865 0.198,0.156 10 false 3a 1.625,0.177 1.771,0.333 0.146,0.156 10 false A 1.635,1.948 1.781,2.104 0.146,0.156 10 false B 2.031,3.146 2.229,3.302 0.198,0.156 10 false 3a
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the navigation antenna assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-3 Always Below 1 Ω
A-3a - B-3a Always Below 1 Ω
A-3 - Body ground Always 10 kΩ or higher
A-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 NAVIGATION ANTENNA CORD SUB-ASSEMBLY

4.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E317092C01
1.479,0.281 1.844,0.521 0.365,0.24 1.469,1.688 1.833,1.927 0.365,0.24 1.24,1.552 1.417,1.271 true 1.354,2.99 1.531,2.719 true 0.26,0.219 0.469,0.396 0.208,0.177 10 false *a 0.333,2.021 0.542,2.198 0.208,0.177 10 false *b 1.615,0.313 1.823,0.49 0.208,0.177 10 false B 1.604,1.729 1.813,1.906 0.208,0.177 10 false C 1.115,1.531 1.323,1.708 0.208,0.177 10 false 3a 1.188,2.969 1.396,3.146 0.208,0.177 10 false 1a
*a Front view of wire harness connector
(to No. 2 Navigation Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the antenna connector from the No. 2 navigation antenna cord sub-assembly.


b.

Disconnect the antenna connector from the radio and display receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-3 - C-1 Always Below 1 Ω
B-3a - C-1a Always Below 1 Ω
B-3 - Body ground Always 10 kΩ or higher
B-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY