Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041700 NAVIGATION / MULTI INFO DISPLAY _0197741 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Navigation Receiver Assembly and Combination Meter  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E280956E20
1.771,1.052 2.083,1.25 0.313,0.198 10 false +S 2.052,0.938 2.365,1.135 0.313,0.198 10 false 19 1.042,1.813 1.354,2.01 0.313,0.198 10 false G8 1.052,2 3.073,2.271 2.021,0.271 10 false Combination Meter Assembly 4.979,0.917 5.292,1.115 0.313,0.198 10 false 17 5.219,1.063 5.74,1.292 0.521,0.229 10 false SPD 5.094,1.844 5.573,2.083 0.479,0.24 10 false G41 5.073,2.01 7,2.219 1.927,0.208 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

Check that the meter / gauge system is operating normally before troubleshooting.



PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C41
1.479,0.438 1.896,0.656 0.417,0.219 0.521,1.99 0.698,1.99 0.698,1.99 0.865,1.344 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.604,0.479 1.917,0.677 0.313,0.198 10 false G8 0.292,1.896 0.604,2.094 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.125,3.875 1.521,4.146 0.396,0.271 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal G8-19 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G8-19 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-17 (SPD) - G8-19 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR