Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041700 NAVIGATION / MULTI INFO DISPLAY _0197741 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Dimmer Signal Circuit  


DESCRIPTION

The combination meter assembly sends an auto dimmer signal to the navigation receiver assembly via this circuit.

When the navigation receiver assembly receives an auto dimmer signal from the combination meter assembly, the panel switch of the navigation receiver assembly dims and the screen changes to the night screen.

WIRING DIAGRAM

E262317E92
0.458,2.094 2.438,2.302 1.979,0.208 10 false Combination Meter Assembly 0.469,1.927 0.698,2.115 0.229,0.188 10 false G8 1.25,1.031 1.677,1.219 0.427,0.188 10 false ACAN 5.021,2.083 6.906,2.26 1.885,0.177 10 false Navigation Receiver Assembly 5.323,0.927 5.521,1.125 0.198,0.198 10 false 3 1.74,0.927 1.927,1.115 0.188,0.188 10 false 4 5.552,1.042 5.979,1.24 0.427,0.198 10 false ADIM 5.031,1.927 5.635,2.125 0.604,0.198 10 false G41

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.

Disconnect the navigation receiver assembly connector.


b.
E140414C60
1.479,0.448 1.958,0.729 0.479,0.281 1.052,1.385 0.76,0.802 0.76,0.802 0.625,0.802 true 0.063,0.063 0.302,0.25 0.24,0.188 10 false *a 1.594,0.521 2.073,0.75 0.479,0.229 10 false G41 0.26,0.698 0.813,0.865 0.552,0.167 10 false ADIM
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G41-3 (ADIM) - Body ground Engine switch on (IG)
Automatic light control sensor covered by hand, and light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-4 (ACAN) - G41-3 (ADIM) Always Below 1 Ω
G8-4 (ACAN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR