Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041700 NAVIGATION / MULTI INFO DISPLAY _0197741 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E321183E01
1.24,0.417 1.396,0.615 0.156,0.198 10 false A 1.24,1.104 1.396,1.302 0.156,0.198 10 false A 1.26,0.188 1.417,0.385 0.156,0.198 10 false 2 1.25,0.875 1.406,1.073 0.156,0.198 10 false 1 2.698,1.115 2.854,1.313 0.156,0.198 10 false B 2.698,0.417 2.854,0.615 0.156,0.198 10 false B 4.26,0.417 4.417,0.615 0.156,0.198 10 false C 4.25,1.135 4.406,1.333 0.156,0.198 10 false C 5.792,0.427 6.104,0.625 0.313,0.198 10 false RA 5.792,1.125 6.104,1.323 0.313,0.198 10 false RA 2.729,0.198 2.885,0.396 0.156,0.198 10 false 2 4.281,0.208 4.438,0.406 0.156,0.198 10 false 2 2.719,0.896 2.875,1.094 0.156,0.198 10 false 3 4.281,0.906 4.438,1.104 0.156,0.198 10 false 3 5.865,0.198 6.021,0.396 0.156,0.198 10 false 3 5.865,0.906 6.021,1.104 0.156,0.198 10 false 5 6.156,0.427 6.865,0.667 0.708,0.24 10 false MAIN 6.177,1.125 6.885,1.365 0.708,0.24 10 false ANT+ 0.01,1.656 1.469,2.031 1.458,0.375 10 false No. 1 Amplifier Antenna Assembly 1.542,1.677 2.833,2.031 1.292,0.354 10 false No. 3 Antenna Cord Sub-assembly 3.01,1.708 4.302,2.063 1.292,0.354 10 false No. 2 Antenna Cord Sub-assembly 4.677,1.719 5.604,2.083 0.927,0.365 10 false Antenna Cord Sub-assembly 5.906,1.917 7.156,2.271 1.25,0.354 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.



Result:
Proceed to
OK
NG



OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)
3.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)
a.
E276819

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the RA navigation receiver assembly connector.


b.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Engine switch on (ACC), radio switch on and FM or AM selected 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E321184C01
1.542,0.104 1.875,0.333 0.333,0.229 1.542,1.667 1.875,1.896 0.333,0.229 1.667,0.125 1.865,0.292 0.198,0.167 10 false A 1.667,1.698 1.844,1.865 0.177,0.167 10 false B 0.26,0.167 0.458,0.354 0.198,0.188 10 false *a 0.302,1.75 0.5,1.938 0.198,0.188 10 false *b
*a Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-1 - B-3 Always Below 1 Ω
A-2 - Body ground Always 10 kΩ or higher
A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E321185C01
1.49,0.094 1.865,0.344 0.375,0.25 1.5,1.792 1.875,2.042 0.375,0.25 0.208,0.177 0.396,0.344 0.188,0.167 10 false *a 0.25,1.885 0.438,2.052 0.188,0.167 10 false *b 1.635,0.135 1.823,0.302 0.188,0.167 10 false B 1.635,1.833 1.823,2 0.188,0.167 10 false C
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 Always Below 1 Ω
B-3 - C-3 Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher
B-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E317097C03
1.583,0.156 1.969,0.396 0.385,0.24 1.552,1.604 1.938,1.844 0.385,0.24 1.052,2.323 1.229,2.323 1.229,2.323 1.583,2.833 true 2.458,2.146 2.313,2.146 2.313,2.146 1.948,2.646 true 0.25,0.229 0.448,0.427 0.198,0.198 10 false *a 0.313,2.021 0.51,2.188 0.198,0.167 10 false *b 1.719,0.188 1.917,0.354 0.198,0.167 10 false C 1.656,1.635 1.917,1.802 0.26,0.167 10 false RA 2.51,2.073 2.906,2.25 0.396,0.177 10 false ANT+ 0.656,2.24 1.063,2.406 0.406,0.167 10 false MAIN
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the navigation receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - RA-3 (MAIN) Always Below 1 Ω
C-3 - RA-5 (ANT+) Always Below 1 Ω
C-2 - Body ground Always 10 kΩ or higher
C-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

8.CHECK NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG