Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0198096 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the certification ECU (smart key ECU assembly). (ex. if a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the body ECU).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short in RDAS to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RDAS to ground when RCO (5 V) output from the ECU is off.


·

Harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

B479912E01
5.229,2.802 6.74,3.219 1.51,0.417 10 false Certification ECU (Smart Key ECU Assembly) 5.99,1.25 6.458,1.552 0.469,0.302 10 false +B 6.01,0.552 6.479,0.854 0.469,0.302 10 false 5V 5.26,0.823 5.729,1.125 0.469,0.302 10 false RCO 5.281,1.521 5.75,1.823 0.469,0.302 10 false RDAS 1.656,1.531 2.125,1.833 0.469,0.302 10 false DATA 1.74,2.208 2.208,2.51 0.469,0.302 10 false GND 1.875,0.844 2.344,1.146 0.469,0.302 10 false +5 2.156,0.844 2.625,1.146 0.469,0.302 10 false 4 2.156,1.531 2.625,1.833 0.469,0.302 10 false 5 2.135,2.135 2.604,2.438 0.469,0.302 10 false 1 4.969,2.021 5.438,2.323 0.469,0.302 10 false 10 4.917,2.219 5.385,2.521 0.469,0.302 10 false G16 4.906,1.615 5.375,1.917 0.469,0.302 10 false G17 4.958,1.438 5.427,1.74 0.469,0.302 10 false 22 4.896,0.938 5.365,1.24 0.469,0.302 10 false G17 4.99,0.74 5.458,1.042 0.469,0.302 10 false 3 0.896,1.323 1.365,1.625 0.469,0.302 10 false IC 0.781,2.833 2.292,3.25 1.51,0.417 10 false Door Control Receiver 0.771,2.667 1.24,2.969 0.469,0.302 10 false G25 5.281,2.219 5.75,2.521 0.469,0.302 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

This DTC is not detected within 10 seconds after the engine switch is turned off from on (IG).

·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the G25 door control receiver connector.

B392000C03
2.25,2 2.833,2.25 0.583,0.25 4.031,2 4.615,2.25 0.583,0.25 1.354,0.75 1.729,0.75 1.729,0.75 1.938,1.333 true 4.948,1.333 5.115,0.75 5.115,0.75 5.448,0.75 true 4.865,1.469 5.031,2.083 5.031,2.083 5.365,2.083 true 0.927,0.677 1.615,0.885 0.688,0.208 10 false E (10) 5.521,0.688 6.271,0.896 0.75,0.208 10 false RCO (3) 5.406,1.99 6.24,2.198 0.833,0.208 10 false RDAS (22) 2.406,2.042 3.094,2.25 0.688,0.208 10 false G16 4.177,2.042 4.865,2.25 0.688,0.208 10 false G17 0.083,0.042 0.771,0.25 0.688,0.208 10 false *a
*a Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-10 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G17-3 (RCO) - Body ground Always 4.5 to 5.5 V pulse generation at regular intervals
G17-22 (RDAS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL RECEIVER

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] AND BODY GROUND)
a.

Disconnect the G25 door control receiver connector.


b.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-5 (DATA) - G17-22 (RDAS) Always Below 1 Ω
G25-4 (+5) - G17-3 (RCO) Always Below 1 Ω
G25-1 (GND) - Body ground Always Below 1 Ω
G16-10 (E) - Body ground Always Below 1 Ω
G25-5 (DATA) or G17-22 (RDAS) - Body ground Always 10 kΩ or higher
G25-4 (+5) or G17-3 (RCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR