Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0198095 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The body ECU receives signals from the certification ECU (smart key ECU assembly). Then, the body ECU activates the back door lock motor.

WIRING DIAGRAM

E329771E01
0.552,1.792 2.323,2.073 1.771,0.281 10 false Back Door Lock Assembly 0.573,1.583 4.094,1.781 3.521,0.198 10 false V2 0.542,1.094 0.917,1.323 0.375,0.229 10 false 2 0.719,1.094 1.094,1.323 0.375,0.229 10 false ACT- 1.458,1.073 1.875,1.302 0.417,0.229 10 false ACT+ 3.052,1 3.427,1.229 0.375,0.229 10 false 1 3,1.198 3.375,1.427 0.375,0.229 10 false 2M 4.771,1.198 5.146,1.427 0.375,0.229 10 false A 4.781,1 5.156,1.229 0.375,0.229 10 false 4 5.094,1.198 5.51,1.427 0.417,0.229 10 false TR+ 4.75,1.906 5.125,2.135 0.375,0.229 10 false 17 4.781,2.135 5.156,2.365 0.375,0.229 10 false A 5.083,2.146 5.531,2.385 0.448,0.24 10 false BDSU 3.01,2.135 3.385,2.365 0.375,0.229 10 false 2D 3.042,1.927 3.417,2.156 0.375,0.229 10 false 4 3.354,2.51 4.969,2.958 1.615,0.448 10 false Instrument Panel Junction Block Assembly 2.594,4.031 2.969,4.26 0.375,0.229 10 false G16 2.635,3.813 3.01,4.042 0.375,0.229 10 false 14 2.281,3.927 2.656,4.156 0.375,0.229 10 false *1 2.333,2.052 2.708,2.281 0.375,0.229 10 false *2 0.729,3.948 1.104,4.177 0.375,0.229 10 false E 0.531,3.938 0.906,4.167 0.375,0.229 10 false 2 1.625,3.927 2,4.156 0.375,0.229 10 false UL 1.917,3.906 2.292,4.135 0.375,0.229 10 false 3 1.927,1.094 2.302,1.323 0.375,0.229 10 false 1 0.563,4.406 1.063,4.615 0.5,0.208 10 false V10 0.552,4.542 2.146,4.969 1.594,0.427 10 false Back Door Opener Switch Assembly 2.969,4.052 3.438,4.281 0.469,0.229 10 false TSW5 3.531,4.052 4,4.281 0.469,0.229 10 false PRG3 3.531,3.583 4,3.813 0.469,0.229 10 false RDA3 4.031,3.583 4.406,3.813 0.375,0.229 10 false G17 4.031,4.052 4.406,4.281 0.375,0.229 10 false G17 4.063,3.385 4.438,3.615 0.375,0.229 10 false 13 4.094,3.854 4.469,4.083 0.375,0.229 10 false 36 4.688,4.042 5.063,4.271 0.375,0.229 10 false G33 4.688,3.594 5.063,3.823 0.375,0.229 10 false G33 4.74,3.385 5.115,3.615 0.375,0.229 10 false 16 4.792,3.844 5.167,4.073 0.375,0.229 10 false 9 2.729,4.521 4.24,5.073 1.51,0.552 10 false Certification ECU (Smart Key ECU Assembly) 5.083,3.594 5.531,3.833 0.448,0.24 10 false RDA 5.083,4.063 5.531,4.302 0.448,0.24 10 false PRG 5.469,4.823 6.344,5.333 0.875,0.51 10 false Body ECU 0.385,5.125 2.76,5.354 2.375,0.229 10 false *1: w/ Smart Entry and Start System 0.385,5.438 2.76,5.667 2.375,0.229 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Before performing the inspection, check that DTC B27B0 (Smart Entry and Start System) (for Entry Function) is not output.*



*: w/ Smart Entry and Start System


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specification.


Result:
Proceed to
w/o Smart Entry and Start System
w/ Smart Entry and Start System



w/o Smart Entry and Start System

2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

w/ Smart Entry and Start System

5.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)
2.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.


b.

Inspect the back door opener switch assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the V2 back door lock assembly connector.


b.

Disconnect the 2M instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V10-3 (UL) - 2D-4 Always Below 1 Ω
V10-3 (UL) or 2D-4 - Body ground Always 10 kΩ or higher
V10-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E329770C01
2.042,0.854 2.438,1.115 0.396,0.26 5.333,0.802 5.729,1.063 0.396,0.26 0.979,1.229 1.313,1.229 1.313,1.229 1.563,1.646 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 2.208,0.906 2.521,1.104 0.313,0.198 10 false A 5.458,0.833 5.771,1.031 0.313,0.198 10 false 2D 0.563,1.146 1.083,1.344 0.521,0.198 10 false BDSU
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-17 (BDSU) - 2D-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK SMART ENTRY AND START SYSTEM (for Entry Function)
a.

Check the smart entry and start system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Smart entry and start system (for Entry Function) operates normally.



Result:
Proceed to
OK
NG



OK

6.INSPECT BACK DOOR LOCK ASSEMBLY

NG

6.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Remove the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL


b.

Inspect the back door lock assembly.

Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the V2 back door lock assembly connector.


b.

Disconnect the 2M instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-1 (ACT+) - 2M-1 Always Below 1 Ω
V2-1 (ACT+) or 2M-1 - Body ground Always 10 kΩ or higher
V2-2 (ACT-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

E320091C01
2.146,0.615 2.51,0.844 0.365,0.229 5.479,0.615 5.844,0.844 0.365,0.229 3.333,1.667 3.583,1.021 3.583,1.021 3.75,1.021 true 2.292,0.646 2.552,0.844 0.26,0.198 10 false A 5.573,0.646 5.99,0.844 0.417,0.198 10 false 2M 0.104,0.083 0.365,0.281 0.26,0.198 10 false *a 3.854,0.958 4.313,1.156 0.458,0.198 10 false TR+
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-4 (TR+) - 2M-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY