The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Push the recording switch and perform voice recording.
Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
Voice can be recorded for up to 5 seconds.
Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.
All check results are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G100 radio and display receiver assembly connector.
Disconnect the Q2 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-4 (MACC) - Q2-15 (MACC) | Always | Below 1 Ω |
| G100-5 (MIN+) - Q2-14 (MCO+) | Always | Below 1 Ω |
| G100-19 (MIN-) - Q2-13 (MCO-) | Always | Below 1 Ω |
| G100-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| G100-4 (MACC) or Q2-15 (MACC) - Body ground | Always | 10 kΩ or higher |
| G100-5 (MIN+) or Q2-14 (MCO+) - Body ground | Always | 10 kΩ or higher |
| G100-19 (MIN-) or Q2-13 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Remove the radio and display receiver assembly with the connector still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G100-19 (MIN-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Map Light Assembly) |
Reconnect the map light assembly with the connector still connected.
Turn the ignition switch ACC.
Connect an oscilloscope to terminals Q2-14 (MCO+) and Q2-13 (MCO-) of the map light assembly connector.
Check the waveform of the telephone microphone assembly using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly is not output. | A |
| A waveform synchronized with the voice input to the map light assembly is output. | B |
A
B
Replace the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL
Check if the same malfunction recurs.
Malfunction does not recur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG