Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0195472 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Dimmer Signal Circuit  


DESCRIPTION

The combination meter assembly sends an auto dimmer signal to the radio and display receiver assembly via this circuit.

When the radio and display receiver assembly receives an auto dimmer signal from the combination meter assembly, the panel switch of the radio and display receiver assembly dims and the screen changes to the night screen.

WIRING DIAGRAM

E298936E09
5.24,1.073 5.885,1.271 0.646,0.198 10 false ADIM 4.958,0.938 5.417,1.135 0.458,0.198 10 false 3 2.073,0.938 2.531,1.135 0.458,0.198 10 false 4 1.573,1.063 2.281,1.26 0.708,0.198 10 false ACAN 0.938,1.771 1.396,1.969 0.458,0.198 10 false G8 0.938,1.938 2.156,2.354 1.219,0.417 10 false Combination Meter Assembly 5.021,1.781 5.479,1.979 0.458,0.198 10 false G100 5.021,1.927 6.698,2.24 1.677,0.313 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (DIMMER SIGNAL)
a.

Disconnect the radio and display receiver assembly connector.


b.
E140414C49
1.427,0.448 2.031,0.729 0.604,0.281 1.052,1.385 0.76,0.802 0.76,0.802 0.625,0.802 true 0.063,0.063 0.302,0.25 0.24,0.188 10 false *a 1.573,0.5 2.063,0.688 0.49,0.188 10 false G100 0.26,0.698 0.813,0.865 0.552,0.167 10 false ADIM
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G100-3 (ADIM) - Body ground Ignition switch ON, automatic light control sensor covered by hand, and light control switch in tail or head position 11 to 14 V
Ignition switch ON, automatic light control sensor not covered by hand, and light control switch in auto position Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G100 radio and display receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G100-3 (ADIM) - G8-4 (ACAN) Always Below 1 Ω
G100-3 (ADIM) or G8-4 (ACAN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR