Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0199688 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the horn button assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45187 3.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B404057C01
2.792,0.625 3.052,0.438 true 3.031,0.313 3.344,0.469 0.313,0.156 10 false *a
*a Cutout
V100155

Protective Tape


Using a screwdriver, insert the screwdriver into the cutout of the lower No. 3 steering wheel cover and detach the claw and guide to remove the lower No. 3 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



Hide 45186 4.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B404058C01
0.396,0.49 0.615,0.656 true 0.229,0.375 0.542,0.531 0.313,0.156 10 false *a
*a Cutout
V100155

Protective Tape


Using a screwdriver, insert the screwdriver into the cutout of the lower No. 2 steering wheel cover and detach the claw and guide to remove the lower No. 2 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY

CAUTION:
B399098C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the horn button assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B409175C01
0,0 0,0 false
V113147

Release in this Direction


Using a T25H "TORX" screwdriver, push in the torsion spring to detach the pin and remove the horn button assembly.

NOTICE:
·

Do not drop the horn button assembly.

·

When disconnecting the horn button assembly, do not pull the airbag wire harness.



HINT:

Insert the T25H "TORX" screwdriver into the installation areas of the lower No. 2 steering wheel cover and lower No. 3 steering wheel cover.



d.
B409176C01
2.104,2.323 2.552,2.5 true 1.938,2.219 2.25,2.375 0.313,0.156 10 false *a
*a Connector Lock
V100155

Protective Tape
V113147

Release in this Direction


Tilt the horn button assembly toward the seat and support it with one hand.


e.

Disconnect the horn connector.


f.

Using a screwdriver, release the connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.