Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM3270E _52 Drivetrain _041684 VF2CM TRANSFER / 4WD / AWD _0201040 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17AA  Transfer Shift Motor Control Circuit High  


DESCRIPTION

This DTC is output when a short to B+ in the transfer shift motor and A.D.D. shift motor drive circuit is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17AA Transfer Shift Motor Control Circuit High
·

Diagnosis Condition: Directly after or while the ignition switch is turned to ON (transfer shift motor not operating)

·

Malfunction Status: Short to B+ in the transfer shift motor and A.D.D. shift motor drive circuits

·

Malfunction Time: 0.5 seconds or more (after the ignition switch is turned to ON, 0.05 seconds or more)

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

A.D.D. actuator (differential motor actuator assembly



PROCEDURE

1.CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR AND A.D.D. SHIFT MOTOR)
a.

Disconnect the C61 4 wheel drive control ECU connector.


b.
C142292C02
1.563,0.635 1.948,0.917 0.385,0.281 1.719,2.26 2.094,2.885 true 1.969,2.25 2.625,2.896 true 1.365,2.25 1.073,2.802 true 1.417,1.771 1.125,1.063 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 2.5,2.927 2.958,3.125 0.458,0.198 10 false TM1 1.99,2.938 2.448,3.135 0.458,0.198 10 false TM2 0.99,0.865 1.448,1.063 0.458,0.198 10 false DM1 0.885,2.865 1.344,3.063 0.458,0.198 10 false DM2 1.635,0.698 2.094,0.896 0.458,0.198 10 false C61
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Transfer shift actuator assembly side:
Tester Connection Condition Specified Condition
C61-8 (TM1) or C61-7 (TM2) - Body ground Ignition switch ON Below 1 V

A.D.D. actuator (differential motor actuator assembly) side:
Tester Connection Condition Specified Condition
C61-2 (DM1) or C61-6 (DM2) - Body ground Ignition switch ON Below 1 V



Result:
Result Proceed to
OK A
NG (transfer shift actuator assembly side) B
NG (A.D.D. actuator (differential motor actuator assembly) side) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

C

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the C61 4 wheel drive control ECU connector.


b.

Disconnect the C74 transfer shift actuator assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C61-8 (TM1) or C74-2 (TM1) - Body ground Ignition switch ON Below 1 V
C61-7 (TM2) or C74-1 (TM2) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the C61 4 wheel drive control ECU connector.


b.

Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C61-2 (DM1) or C57-1 (DM1) - Body ground Ignition switch ON Below 1 V
C61-6 (DM2) or C57-2 (DM2) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR