Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM › 2015.08–2016.01
RM3270E _52 Drivetrain _041684 VF2CM TRANSFER / 4WD / AWD _0201040 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

This DTC is output when a malfunction in the L4 detection switch is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P2772 Four Wheel Drive (4WD) Low Switch Circuit Range / Performance
·

Diagnosis Condition: Ignition switch turned to ON (3 seconds elapse after ignition switch is turned to ON)

·

Malfunction Status: L4 detection switch is stuck OFF when the vehicle is in L4

·

Malfunction Time: 10 seconds or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C345091E01
2.625,0.313 2.938,0.51 0.313,0.198 10 false IG 3.125,0.875 3.74,1.073 0.615,0.198 10 false EXI4 3.521,0.875 3.677,1.073 0.156,0.198 10 false 5 1.354,1.802 1.667,2 0.313,0.198 10 false A4 1.333,1.969 4.719,2.167 3.385,0.198 10 false Skid Control ECU (Brake Actuator Assembly) 2.625,2.604 2.938,2.802 0.313,0.198 10 false +B 3.208,3.198 3.521,3.396 0.313,0.198 10 false L4 3.448,3.198 3.76,3.396 0.313,0.198 10 false 12 6.5,3.563 6.813,3.76 0.313,0.198 10 false IG 1.396,3.75 1.854,3.948 0.458,0.198 10 false C41 1.385,3.906 1.844,4.104 0.458,0.198 10 false ECM 1.625,4.469 2.083,4.667 0.458,0.198 10 false GND 1.417,4.469 1.729,4.667 0.313,0.198 10 false 10 1.302,4.885 1.76,5.083 0.458,0.198 10 false C74 1.323,5.052 3.844,5.25 2.521,0.198 10 false Transfer Shift Actuator Assembly 2.333,4.719 4.083,4.917 1.75,0.198 10 false L4 Detection Switch 3.635,4.469 3.948,4.667 0.313,0.198 10 false L4 3.885,4.469 4.042,4.667 0.156,0.198 10 false 9 5.25,4.469 5.406,4.667 0.156,0.198 10 false 3 5.448,4.469 6.063,4.667 0.615,0.198 10 false 4WDL 5.25,5.083 5.708,5.281 0.458,0.198 10 false C60 5.271,5.25 7.156,5.448 1.885,0.198 10 false 4 Wheel Drive Control ECU

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the C74 transfer shift actuator assembly connector.


c.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the C41 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-3 (4WDL) - C74-9 (L4) Always Below 1 Ω
C74-10 (GND) - Body ground Always Below 1 Ω
C60-3 (4WDL) or C74-9 (L4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY
a.

Turn the ignition switch to ON.


b.

Turn the transfer position switch to L4.


c.

Turn the ignition switch off.


d.

Disconnect the C74 transfer shift actuator assembly connector.


e.
C325774C01
1.865,1.958 2.24,2.688 false 1.479,1.958 1.167,2.667 false 0.198,0.271 0.51,0.469 0.313,0.198 10 false *a 1.021,2.688 1.479,2.885 0.458,0.198 10 false GND 2.219,2.729 2.531,2.927 0.313,0.198 10 false L4
*a Component without harness connected
(Transfer Shift Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L4) - 10 (GND) Transfer L4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY