Home › Drivetrain › RC61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT
RM3270E _52 Drivetrain _041683 RC61F MANUAL TRANSMISSION / TRANSAXLE _0201478 MANUAL TRANSMISSION UNIT A

RC61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 31230 1.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 2.REMOVE RELEASE FORK SUPPORT

Hide 84210 3.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

Hide 4.REMOVE BACK-UP LIGHT SWITCH BRACKET

a.
C333523

Remove the 3 bolts and back-up light switch brackets.


Hide 89413B 5.REMOVE TRANSMISSION REVOLUTION SENSOR (w/ Intelligent Manual Transmission Switch)

Hide 84545 6.REMOVE NEUTRAL POSITION SWITCH

Hide 33111A 7.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C336098

Remove the manual transmission filler plugs, drain plug sub-assembly and 2 gaskets from the manual transmission case sub-assembly.


b.

Using a 10 mm hexagon wrench, remove the with head straight screw plug from the rear transmission case.


Hide 33275B 8.REMOVE SHAFT DETENT BALL

a.
C339096

Using a 6 mm hexagon wrench, remove the 4 shift detent ball plugs from the rear transmission case.


b.

Remove the 4 shift detent ball compression springs and 4 shift detent balls from the rear transmission case.


Hide 33292A 9.REMOVE LOCK BALL PIN

a.
C323793

Using a 10 mm hexagon wrench, remove the No. 2 with head straight screw plug from the rear transmission case.


b.

Remove the lock ball pin and shift and select lever spring from the rear transmission case.


Hide 33506F 10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C323502

Remove the 4 bolts and then remove the floor shift control shift lever retainer sub-assembly and control shift lever retainer gasket from the rear transmission case sub-assembly.


Hide 33521 11.REMOVE SHIFT LEVER HOUSING

a.
C323504

Remove the bolt and shift lever housing.

NOTICE:

Do not damage the sealing surface of the control shift lever retainer sub-assembly



Hide 33121G 12.REMOVE MANUAL TRANSMISSION CASE COVER

a.
C323511

Remove the 4 bolts and manual transmission case cover from the rear transmission case.


Hide 33321G 13.UNSTAKE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C323791

Using a chisel and hammer, unstake the manual transmission output shaft rear set nut.


Hide 33321G 14.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C323512C03
2.927,0.583 2.927,0.396 false 2.448,0.906 2.594,1.094 2.594,1.094 2.771,1.094 false 0.438,1.573 0.563,1.573 0.563,1.573 0.563,1.958 false 1.542,2.469 2.74,3.073 2.74,3.073 2.927,3.073 true 0.479,3.729 0.75,3.875 false 2.823,0.188 3.135,0.344 0.313,0.156 10 false *1 2.99,3.01 3.146,3.208 0.156,0.198 10 true A 0.094,1.49 0.552,1.688 0.458,0.198 10 false SST 2.833,1.01 2.99,1.208 0.156,0.198 10 true A 0.146,3.656 0.438,3.844 0.292,0.188 10 true SST
*1 Input Shaft


Engage the gear, and then secure the input shaft using SST.

SST
09322-35010  (09322-03010, 09322-03020, 09322-03030, 90105-12087, 90170-12030, 94622-51200)

HINT:
·

Install SST securely so that the part labeled A is in-line with the input shaft.

·

Make sure that the part labeled A moves back and forth by hand after installing SST.




b.
C325392N01
0.604,1.615 1.604,1.25 true 0.281,1.573 0.74,1.771 0.458,0.198 10 false SST

Using SST, remove the manual transmission output shaft rear set nut from the output shaft.

SST
09326-35010  (09326-03010)


Hide 31111 15.REMOVE CLUTCH HOUSING

a.
C323803

Remove the 10 bolts.


b.

Using a plastic-faced hammer, carefully tap off the clutch housing to remove it.


Hide 33131D 16.REMOVE FRONT BEARING RETAINER

a.
C323797

Remove the 11 bolts.


b.
C333516

Using a screwdriver wrapped in protective tape, remove the front bearing retainer by prying the points in the illustration.

NOTICE:
·

Do not damage the sealing surface of the clutch housing and manual transmission case sub-assembly.

·

Do not damage the sealing surface of the front bearing retainer and manual transmission case sub-assembly.




Hide 33124C 17.REMOVE NO. 1 OIL RECEIVER PIPE

a.

Remove the No. 1 oil receiver pipe from the front bearing retainer.


Hide 33131A 18.REMOVE FRONT TRANSMISSION BEARING RETAINER OIL SEAL

Hide 33411E 19.REMOVE COUNTER GEAR SHAFT NUT

a.
C323798

Using a chisel and hammer, unstake the counter gear shaft nut.


b.
C334264N01
1.708,3.26 1.333,2.417 1.333,2.417 1.167,2.417 true 2.083,3.646 2.333,4.333 2.333,4.333 2.5,4.333 true 0.833,2.333 1.292,2.531 0.458,0.198 10 false SST 2.542,4.24 3,4.438 0.458,0.198 10 false SST

Using SST, hold the output shaft.

SST
09326-35010  (09326-03010)
09326-71030  


c.

Using a 41 mm socket wrench, remove the counter gear shaft nut.


Hide 33311T 20.REMOVE INPUT SHAFT SNAP RING

a.
C323800

Using snap ring pliers, remove the input shaft snap ring.


Hide 33311G 21.REMOVE FRONT BEARING SHAFT SNAP RING

a.
C323801

Using a snap ring expander, remove the front bearing shaft snap ring.


Hide 22.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C323802

Remove the reverse idler gear shaft bolt and gasket from the reverse idler gear shaft.


Hide 33101 23.REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to remove the manual transmission case sub-assembly.


a.
C333528

Remove the 12 bolts.


b.
C334031

In order to prevent the reverse idler gear from falling when removing the transmission case, set the manual transmission assembly on its side so that the installation hole of the reverse idler gear stopper bolt is facing upward as shown in the illustration.


c.
C329001C01
1.594,0.885 1.927,0.333 1.927,0.333 2.083,0.333 true 2.115,0.24 2.344,0.438 0.229,0.198 10 false *a 0.323,2.646 0.51,2.833 0.188,0.188 10 false *1 2.135,4.333 2.323,4.521 0.188,0.188 10 false *1
*1 Straight Pin
*a Protective Tape


Using a screwdriver wrapped in protective tape, separate the transmission case sub-assembly and intermediate plate by prying at the points shown in the illustration.

NOTICE:

Do not damage the sealing surfaces of the manual transmission case sub-assembly and transmission intermediate plate.



d.
C334781

Place wooden blocks or other objects underneath the rear transmission case to securely support it as shown in the illustration.


e.

Remove the manual transmission case sub-assembly from the rear transmission case.


Hide 33461 24.REMOVE REVERSE IDLER GEAR

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the reverse idler gear, have the other person hold the transmission in place.


a.
C336099

Remove the reverse idler gear and front oil receiver from the transmission unit.


b.

Remove the No. 2 oil receiver from the reverse idler gear shaft.


c.
C323806

Remove the reverse idler gear bearing and reverse idler gear from the reverse idler gear shaft.


Hide 33261C 25.REMOVE SHIFT AND SELECT LEVER SHAFT SUB-ASSEMBLY

a.
C336100

Remove the shift and select lever shaft sub-assembly from the transmission unit.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the shift and select shaft, have the other person hold the transmission in place.



Hide 33268C 26.REMOVE SHIFT INTERLOCK PLATE STOPPER

a.
C336101

Remove the 2 bolts and shift interlock plate stopper from the transmission unit.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the shift interlock plate stopper, have the other person hold the transmission in place.



Hide 33109C 27.REMOVE MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY

a.
C323835

Remove the 2 bolts and transmission oil separator sub-assembly (front side).

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the manual transmission oil separator sub-assembly, have the other person hold the transmission in place.



Hide 33449B 28.REMOVE TRANSMISSION MAGNET

a.
C333991

Remove the transmission magnet from the transmission intermediate plate.

CAUTION:

Since the manual transmission is very heavy, perform these procedures with 2 people. While one person is removing the manual transmission magnet, have the other person hold the transmission in place.



Hide 33112G 29.REMOVE REAR TRANSMISSION CASE

a.
C334019N01
1.365,2.958 1.729,3.208 1.729,3.208 2,3.208 false 2.104,3.125 2.469,3.281 0.365,0.156 10 false SST

Using SST, set the transmission unit.

SST
09310-71010  

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to set the transmission unit.



b.
C323824N01
1.406,3.01 2.146,2.76 false 1.115,2.948 1.573,3.146 0.458,0.198 10 false SST

Stand the manual transmission upright as shown in the illustration.

CAUTION:

Since the manual transmission unit is very heavy, 2 people are needed to stand the manual transmission upright as shown in the illustration.



c.
C324016

Remove the rear output shaft bearing.


d.
C323825

Remove the rear transmission case and intermediate plate.


e.

Remove the intermediate plate from the rear transmission case.


f.
C333737

Remove the transmission oil separator sub-assembly (rear side).


Hide 33124L 30.REMOVE NO. 3 OIL RECEIVER PIPE

a.
C336102

Remove the No. 3 oil receiver pipe from the rear transmission case.


Hide 31.REMOVE SHIFT FORK AND SHIFT FORK SHAFT ASSEMBLY

a.
C333992C01
0,0 0,0 false
V113147

Remove in this Direction


Move the No. 2 hub sleeve as shown in the illustration and remove the No. 3 gear shift fork from SST as shown in the illustration.


b.
C333994C02
0.76,1.604 0.958,1.979 0.958,1.979 1.219,1.979 true 1.313,1.615 1.51,1.99 1.51,1.99 1.771,1.99 true 1.292,1.906 1.448,2.104 0.156,0.198 10 true 1 1.865,1.896 2.021,2.094 0.156,0.198 10 true 2
V113147

Remove in this Direction


Slide the No. 3 gear shift fork from position 1 to 2 and then remove the No. 3 gear shift fork together with the No. 3 gear shift fork shaft.


c.
C333996C01
1.833,0.365 2.042,0.365 2.042,0.365 2.271,0.823 true 0.458,1.271 0.167,2 0.167,2 0.417,2 true 1.198,3.354 1.406,3.354 1.406,3.354 1.635,3.813 true 1.615,0.271 1.927,0.469 0.313,0.198 10 false *1 0.5,1.927 0.813,2.125 0.313,0.198 10 false *2 0.99,3.281 1.302,3.479 0.313,0.198 10 false *3
*1 No. 2 Transmission Hub Sleeve
*2 No. 1 Transmission Hub Sleeve
*3 No. 4 Transmission Hub Sleeve
V113147

Remove in this Direction


Slide the No. 2 and No. 1 hub sleeves as shown in the illustration.


d.

Remove the bolt from the No. 4 gear shift fork, and then slide the No. 4 gear shift fork shaft as shown in the illustration.


e.
C333997C01
0,0 0,0 false
V113147

Remove in this Direction


Move the shift fork and shift fork shaft assembly as shown in the illustration.

NOTICE:

Move the 3 shift fork shafts together.



f.
C333998

Remove the shift fork and shift fork shaft sub-assembly from the counter gear.

NOTICE:

Do not drop the No. 4 gear shift fork.



g.
C336103

Remove the No. 4 gear shift fork.


Hide 33321 32.REMOVE OUTPUT SHAFT

a.
C336108C01
2.021,0.677 2.26,0.469 2.26,0.469 2.521,0.469 false 0.729,0.563 0.979,0.563 0.979,0.563 1.208,0.656 false 0.521,0.51 0.833,0.667 0.313,0.156 10 false *1 2.563,0.396 2.875,0.552 0.313,0.156 10 false *2
*1 Input Shaft
*2 Counter Gear


Expand SST to the left and right.


b.
C336126

Remove the output shaft from the transmission unit.


c.

Remove the output shaft spacer and rear output shaft bearing shim.


Hide 33311D 33.REMOVE INPUT SHAFT BEARING

a.
C336106

Remove the input shaft bearing from the input shaft.


Hide 33369B 34.REMOVE NO. 4 SYNCHRONIZER RING

a.
C336107

Remove the No. 4 synchronizer ring from the input shaft.


Hide 33311 35.REMOVE INPUT SHAFT

a.

Remove the input shaft from SST.


Hide 33421 36.REMOVE COUNTER GEAR

a.

Remove the counter gear from SST.


Hide 33411H 37.REMOVE COUNTER GEAR REAR BEARING OR ROLLER

a.
C323842

Remove the bolt and bearing lock plate.


b.
C323843C01
0.708,3.167 1.406,2.917 true 1.563,0.667 0.417,0.396 0.417,0.396 0.865,0.688 true 0.375,3.115 0.833,3.313 0.458,0.198 10 false SST 0.198,0.281 0.51,0.479 0.313,0.198 10 false *a
*a Groove of the Rear Transmission Case


Using SST, remove the counter gear rear bearing or roller (outer) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33321N 38.REMOVE FRONT OUTPUT SHAFT BEARING

a.
C323844C01
0.823,0.667 0.448,0.302 0.448,0.302 1.625,0.667 true 0.542,2.865 0.698,3.135 false 0.25,0.188 0.563,0.344 0.313,0.156 10 false *a 0.75,3.156 1.208,3.354 0.458,0.198 10 false SST
*a Groove of the Rear Transmission Case


Using SST, remove the front output shaft bearing (outer race) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33321A 39.REMOVE REAR OUTPUT SHAFT BEARING

a.
C323846C01
0.396,0.677 1.875,0.208 1.875,0.208 1.188,0.667 true 2.24,3.042 2.875,2.427 false 1.948,0.104 2.26,0.302 0.313,0.198 10 false *a 1.906,3 2.365,3.198 0.458,0.198 10 false SST
*a Groove of the Rear Transmission Case


Using SST, remove the rear output shaft bearing (outer) from the rear transmission case.

SST
09308-00010  

NOTICE:

Do not damage the contact surfaces of the rear transmission case.


HINT:

Align the groove of the rear transmission case with the claws of SST.



Hide 33261K 40.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C323848N01
2.375,1.531 2.146,1.063 2.146,1.063 2.438,1.031 false 1.813,0.969 2.271,1.167 0.458,0.198 10 false SST

Using SST, remove the shift and select lever shaft needle roller bearing from the rear transmission case sub-assembly.

SST
09950-70010  (09951-07200)
09950-60010  (09951-00230)


Hide 33111C 41.REMOVE TRANSMISSION CASE PLUG

a.
C323849N02
2.719,0.281 2.969,0.323 2.969,0.323 2.792,0.583 false 3.031,0.281 3.427,0.5 0.396,0.219 10 false SST

Using SST, remove the transmission case plug from the rear transmission case sub-assembly.

SST
09950-70010  (09951-07200)
09950-60010  (09951-00230)


Hide 33242L 42.REMOVE SHIFT FORK SHAFT BEARING

a.
C323851C02
2.156,0.448 2.354,0.51 false 0.083,0.49 0.396,0.646 0.313,0.156 10 false *a 1.24,0.396 1.427,0.573 0.188,0.177 10 true *b 1.885,0.375 2.344,0.573 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 2 shift fork shaft bearings (rear side) from the rear transmission case sub-assembly.

SST
09319-60020  


Hide 33261K 43.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C336109C01
2.76,0.396 2.938,0.396 false 0.229,0.552 0.531,0.75 0.302,0.198 10 true *a 1.26,0.542 1.49,0.75 0.229,0.208 10 true *b 3.021,0.323 3.323,0.552 0.302,0.229 10 true SST
*a Turn
*b Hold


Using SST, remove the shift and select lever shaft needle roller bearing (front side) from the front transmission case sub-assembly.

SST
09319-60020  


Hide 33242L 44.REMOVE SHIFT FORK SHAFT BEARING

a.
C323870C02
2.104,0.333 2.417,0.49 false 1.271,0.729 1.479,0.906 0.208,0.177 10 true *a 0.156,0.531 0.365,0.708 0.208,0.177 10 true *b 1.792,0.281 2.25,0.479 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 2 shift fork shaft bearings (front side) from the front transmission case sub-assembly.

SST
09319-60020  


Hide 33261C 45.REMOVE SHIFT AND SELECT LEVER SHAFT

a.
C336110

Using a snap ring expander, remove the e-ring from the shift and select lever shaft.


b.
C323872

Remove the bolt from the inner select lever.


c.
C338342

Using a 5 mm pin punch and hammer, tap out the straight pin.


d.

Remove the shift interlock plate sub-assembly and inner select lever (shift and select cam, No. 2 lock ball pin and select return No. 1 compression spring) from the shift and select lever shaft.


e.
C323890

Remove the shift and select cam, No. 2 lack ball pin and select return No. 1 compression spring from the inner select lever.


f.
C323873

Using 2 screwdrivers and a hammer, tap off the snap ring.

HINT:

Use a piece of cloth to prevent the snap ring from flying off.



g.

Remove the shift arm pivot and shift arm from the shift interlock plate sub-assembly.


Hide 33243G 46.REMOVE NEEDLE ROLLER BEARING

a.
C329827C01
1.896,0.552 2.344,1.042 true 1.896,1.042 2.167,1.281 false 1.115,2.031 0.635,1.25 0.635,1.25 1.094,1.594 false 1.156,3 0.542,3.198 0.542,3.198 0.667,2.875 true 1.698,0.438 2.01,0.594 0.313,0.156 10 false *1 1.708,0.927 2.021,1.083 0.313,0.156 10 false *2 0.323,1.125 0.781,1.323 0.458,0.198 10 false SST 0.219,3.188 0.677,3.385 0.458,0.198 10 false SST
*1 Needle Roller Bearing
*2 Shift Arm


Using SST and a press, remove the needle roller bearing from the shift arm.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)
09527-20011  


Hide 33243A 47.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C336111

Remove the bolt and No. 2 gear shift fork from the No. 2 gear shift fork shaft.


b.

Remove the No. 2 gear shift fork shaft from the No. 1 gear shift fork head.


c.
C336973

Place a cloth on 2 V-blocks, set the No. 2 gear shift fork shaft on the cloth, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the gear shift fork shaft.




d.

Using a 5 mm pin punch and hammer, tap out the slotted pin.


e.

Remove the No. 2 gear shift head from the No. 2 gear shift fork shaft.


Hide 33245G 48.REMOVE NO. 4 GEAR SHIFT FORK SHAFT

a.

Remove the No. 4 gear shift fork from the No. 4 gear shift fork shaft.


b.
C336969

Place a cloth on 2 V-blocks, set the No. 4 gear shift fork shaft on the cloth, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the gear shift fork shaft.




c.

Using a 5 mm pin punch and hammer, tap out the slotted pin.


d.

Remove the No. 4 gear shift head from the No. 4 gear shift fork shaft.


Hide 33242 49.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C323878

Remove the bolt and No. 1 gear shift fork from the No. 1 gear shift fork shaft.


b.
C336971

Place a cloth on 2 V-blocks, set the No. 1 gear shift fork shaft on the cloth, and then hold the shaft in place as shown in the illustration.

CAUTION:
·

Perform this procedure with 2 people.

·

Make sure to protect the gear shift fork shaft with a cloth before performing this procedure. If the gear shift fork shaft is damaged, shifting operations will worsen.

·

Firmly secure the gear shift fork shaft.




c.

Using a 5 mm pin punch and hammer, tap out the slotted pin.


d.

Remove the No. 1 gear shift head from the No. 1 gear shift fork shaft.


Hide 33244D 50.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C323880

Remove the bolt and No. 3 gear shift fork from the No. 3 gear shift fork shaft.