Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2015.08–2016.01
RM3270E _57 Power Source / Network _041704 NETWORKING _0201720 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Power Back Door ECU Communication Stop Mode  


DESCRIPTION

Detection Item Detection Item Trouble Area
Power Back Door ECU Communication Stop Mode Either condition is met:
·

"Back Door" is not displayed on the "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Back Door ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of multiplex network door ECU

·

Multiplex network door ECU ground circuit

·

Multiplex network door ECU CAN branch wire or connector

·

Multiplex network door ECU



WIRING DIAGRAM

C250990E08
5.208,5.094 6.99,5.271 1.781,0.177 10 false Multiplex Network Door ECU 5.583,4.375 6.25,4.583 0.667,0.208 10 false GND 5.583,3.708 6.25,3.917 0.667,0.208 10 false IG 5.583,3.125 6.25,3.333 0.667,0.208 10 false B 5.583,2.417 6.25,2.625 0.667,0.208 10 false ECUB 5.583,0.75 6.25,0.958 0.667,0.208 10 false CANP 5.583,1.167 6.25,1.375 0.667,0.208 10 false CANN 5.208,2.427 5.875,2.635 0.667,0.208 10 false V12 5.219,3.135 5.885,3.344 0.667,0.208 10 false V13 5.208,3.729 5.875,3.938 0.667,0.208 10 false V12 5.219,4.365 5.885,4.573 0.667,0.208 10 false V13 5.292,3.521 5.958,3.729 0.667,0.208 10 false 7 5.302,4.146 5.969,4.354 0.667,0.208 10 false 7 5.292,2.927 5.958,3.135 0.667,0.208 10 false 8 5.292,2.219 5.958,2.427 0.667,0.208 10 false 1 3.531,2.26 4.385,2.448 0.854,0.188 10 false ECU-B NO.1 3.792,2.969 4.646,3.156 0.854,0.188 10 false PBD 3.625,3.573 4.542,3.823 0.917,0.25 10 false IG1 NO.5 1.438,3.729 2.781,3.927 1.344,0.198 10 false from IG1 NO.2 Relay 1.948,3.125 2.719,3.354 0.771,0.229 10 false from Battery 1.948,2.396 2.719,2.625 0.771,0.229 10 false from Battery 5.219,1.156 5.885,1.365 0.667,0.208 10 false V12 5.219,0.74 5.885,0.948 0.667,0.208 10 false V12 5.26,0.958 5.927,1.167 0.667,0.208 10 false 14 5.25,0.521 5.917,0.729 0.667,0.208 10 false 13 1.677,0.604 2.344,0.813 0.667,0.208 10 false 1 1.677,1.031 2.344,1.24 0.667,0.208 10 false 2 0.427,1.563 1.958,1.771 1.531,0.208 10 false G128 0.438,1.74 2.74,2 2.302,0.26 10 false No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch ON and wait at least 2.2 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX NETWORK DOOR ECU CAN BRANCH WIRE)
a.
C251435C22
0.313,1.042 0.76,1.302 0.448,0.26 2.708,1.688 2.406,1.688 2.406,1.688 2.229,1.188 true 2.719,1.385 2.49,1.385 2.49,1.385 2.313,1.188 true 2.771,1.302 3.188,1.469 0.417,0.167 10 false CANP 2.75,1.604 3.167,1.771 0.417,0.167 10 false CANN 0.406,1.094 0.719,1.292 0.313,0.198 10 false V12 0.135,0.115 0.552,0.281 0.417,0.167 10 false *a
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V12-13 (CANP) - V12-14 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MULTIPLEX NETWORK DOOR ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - BATTERY AND BODY GROUND)
a.
C278775C09
0.542,2.375 0.938,2.625 0.396,0.25 0.375,0.885 0.771,1.135 0.396,0.25 2.323,0.917 2.5,0.667 2.5,0.667 2.667,0.667 true 1.698,0.958 2.167,0.25 2.167,0.25 2.417,0.25 true 1.667,2.583 1.417,3 1.417,3 1.25,3 true 1.833,2.583 2.021,2.917 2.021,2.917 2.188,2.917 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.448,0.927 0.802,1.135 0.354,0.208 10 false V12 0.615,2.417 0.969,2.625 0.354,0.208 10 false V13 2.469,0.177 2.823,0.385 0.354,0.208 10 false IG 2.729,0.583 3.25,0.833 0.521,0.25 10 false ECUB 2.25,2.833 2.771,3.083 0.521,0.25 10 false GND 1.135,2.917 1.656,3.167 0.521,0.25 10 false B
*a Rear view of wire harness connector
(to Multiplex Network Door ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the multiplex network door ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V12-1 (ECUB) - Body ground Always 11 to 14 V
V13-8 (B) - Body ground Always 11 to 14 V
V12-7 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR