Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2015.08–2016.01
RM3270E _55 Steering _041697 STEERING COLUMN _0201959 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock does not Lock  


DESCRIPTION

The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Steering Lock does not Lock
Entry&Start
·

All items

Click here(Click here)


-

WIRING DIAGRAM

C326207E11
1.01,1.552 3.365,1.927 2.354,0.375 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly)* 1.021,1.396 1.792,1.573 0.771,0.177 10 false I4 1.198,1.01 1.354,1.208 0.156,0.198 10 false 3 1.396,1.104 1.552,1.302 0.156,0.198 10 false E 2.552,0.698 2.865,0.896 0.313,0.198 10 false 11 2.292,0.688 2.604,0.885 0.313,0.198 10 false P2 3.083,0.802 3.542,1 0.458,0.198 10 false G16 3.177,0.615 3.333,0.813 0.156,0.198 10 false 8 3.448,0.698 3.604,0.896 0.156,0.198 10 false P 3.823,0.208 4.135,0.406 0.313,0.198 10 false +B 4.354,0.896 4.667,1.094 0.313,0.198 10 false IC 4.854,1.729 5.313,1.927 0.458,0.198 10 false G16 4.948,1.552 5.104,1.75 0.156,0.198 10 false 5 4.563,1.708 5.021,1.906 0.458,0.198 10 false LIN 6.25,0.479 7.094,0.667 0.844,0.188 10 false from Battery 5.365,1.563 5.521,1.76 0.156,0.198 10 false 5 5.573,1.75 6.031,1.948 0.458,0.198 10 false LIN 5.052,0.635 6.188,0.969 1.135,0.333 10 false STRG LOCK/AM2 NO. 1 5.573,2.302 6.031,2.5 0.458,0.198 10 false IGE 5.365,2.167 5.521,2.365 0.156,0.198 10 false 3 4.906,2.104 5.219,2.302 0.313,0.198 10 false 17 4.854,2.281 5.313,2.479 0.458,0.198 10 false G16 4.427,2.271 5.042,2.469 0.615,0.198 10 false SLR+ 3.438,2.781 4.052,2.979 0.615,0.198 10 false RDA3 3.427,3.271 4.042,3.469 0.615,0.198 10 false PRG3 3.146,2.615 3.458,2.813 0.313,0.198 10 false 13 3.094,2.792 3.552,2.99 0.458,0.198 10 false G17 3.083,3.271 3.542,3.469 0.458,0.198 10 false G17 3.146,3.083 3.458,3.281 0.313,0.198 10 false 36 3.365,3.76 4.885,4.135 1.521,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.344,4.323 7.146,4.719 1.802,0.396 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 5.354,4.188 5.813,4.385 0.458,0.198 10 false G19 2.542,2.781 3,2.979 0.458,0.198 10 false G33 2.531,3.26 2.99,3.458 0.458,0.198 10 false G33 2.583,2.615 2.896,2.813 0.313,0.198 10 false 16 2.625,3.083 2.781,3.281 0.156,0.198 10 false 9 2.167,2.781 2.625,2.979 0.458,0.198 10 false RDA 2.167,3.25 2.625,3.448 0.458,0.198 10 false PRG 1.646,3 2.26,3.198 0.615,0.198 10 false DCTY 1.365,2.99 1.677,3.188 0.313,0.198 10 false A 1.333,2.813 1.646,3.01 0.313,0.198 10 false 18 0.719,2.99 1.031,3.188 0.313,0.198 10 false 2L 0.76,2.813 0.917,3.01 0.156,0.198 10 false 4 1.771,3.771 2.469,3.958 0.698,0.188 10 false Body ECU 0.51,3.781 1.615,4.354 1.104,0.573 10 false Instrument Panel Junction Block Assembly 1.458,5.479 3.063,5.833 1.604,0.354 10 false Front Door Courtesy Light Switch Assembly RH 1.469,5.344 2.177,5.51 0.708,0.167 10 false N1 0.833,6.333 2.448,6.531 1.615,0.198 10 false : LIN Communication Line 5.583,2.823 6.042,3.021 0.458,0.198 10 false GND 5.375,2.698 5.531,2.896 0.156,0.198 10 false 1 4.208,6.188 6.125,6.375 1.917,0.188 10 false *: for Automatic Transmission 5.354,1.188 5.51,1.385 0.156,0.198 10 false 7 5.583,1.344 5.74,1.542 0.156,0.198 10 false B 1.563,4.906 1.719,5.104 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P* and then open a door.

*: for Automatic Transmission



·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, confirm that the problem does not recur.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transmission


Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for Automatic Transmission), and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (L CODE CHECK)

NG

9.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
2.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:
Reasons for verification failure:
·

The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the G19 steering lock ECU (steering lock actuator assembly) connector.


b.
C326201C01
1.542,0.813 1.969,1.094 0.427,0.281 0.875,3.042 1.052,3.042 1.052,3.042 1.208,2.5 false 2.708,1.979 2.521,1.979 2.521,1.979 2.219,2.479 false 1.625,0.875 2.083,1.073 0.458,0.198 10 false G19 0.281,0.313 0.594,0.51 0.313,0.198 10 false *a 2.75,1.917 2.906,2.115 0.156,0.198 10 false B 0.563,2.958 1.021,3.156 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
G19-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the G19 steering lock ECU connector.


b.

Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P*.

*: for Automatic Transmission



c.
C241547C68
0.323,2.917 1.646,3.031 1.323,0.115 2.333,2.969 2.76,3.073 0.427,0.104 1.594,4.073 2.417,4.188 0.823,0.115 0.198,0.833 0.615,1.104 0.417,0.271 0.844,1.833 1.854,1.104 false 2.833,1.833 2.292,1.104 false 2.542,3.198 2.542,3.073 false 1.99,4.063 1.99,3.938 false 0.979,3.167 0.979,3.042 false 0.906,3.167 1.219,3.323 0.313,0.156 10 false *b 1.906,3.76 2.219,3.917 0.313,0.156 10 false *c 2.469,3.208 2.781,3.365 0.313,0.156 10 false *b 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 0.708,1.865 1.167,2.063 0.458,0.198 10 false IGE 2.74,1.854 3.198,2.052 0.458,0.198 10 false GND 2.979,4.063 3.365,4.24 0.385,0.177 10 false GND 0.281,0.896 0.646,1.094 0.365,0.198 10 false G19
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency
Item Content
Tester Connection G19-3 (IGE) - G19-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating

HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.



*: for Automatic Transmission




Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G19 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-3 (IGE) - G16-17 (SLR+) Always Below 1 Ω
G19-3 (IGE) - Body ground Always 10 kΩ or higher
G16-17 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the G19 steering lock ECU (steering lock actuator assembly) connector.


b.
C157849C93
0.292,0.885 0.74,1.177 0.448,0.292 1.938,1.917 2.688,2.677 true 0.375,0.271 0.667,0.521 0.292,0.25 10 false *a 0.385,0.958 0.76,1.208 0.375,0.25 10 false G19 2.729,2.688 3.177,2.896 0.448,0.208 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

7.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (L CODE CHECK)
8.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION

OK:

Front door courtesy light switch assembly RH is normal.


Result:
Proceed to
OK
NG




OK

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

10.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the N1 front door courtesy light switch assembly RH connector.


b.

Disconnect the 2L instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 - 2L-4 Always Below 1 Ω
N1-1 - Body ground Always 10 kΩ or higher
2L-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Remove the body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

C280674C04
1.271,0.042 1.594,0.323 0.323,0.281 5.094,0.073 5.417,0.333 0.323,0.26 5.24,1.896 5.073,1.896 5.073,1.896 4.656,1.354 true 0.271,0.156 0.583,0.354 0.313,0.198 10 false *a 1.354,0.115 1.667,0.313 0.313,0.198 10 false 2L 5.219,0.125 5.531,0.323 0.313,0.198 10 false A 5.354,1.823 5.813,2.021 0.458,0.198 10 false DCTY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2L-4 - A-18 (DCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY ECU)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-13 (RDA3) - G33-16 (RDA) Always Below 1 Ω
G17-13 (RDA3) - Body ground Always 10 kΩ or higher
G33-16 (RDA) - Body ground Always 10 kΩ or higher
G17-36 (PRG3) - G33-9 (PRG) Always Below 1 Ω
G17-36 (PRG3) - Body ground Always 10 kΩ or higher
G33-9 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE BODY ECU
a.

Replace the body ECU with a new one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK STEERING LOCK CONDITION
14.CHECK STEERING LOCK CONDITION
a.

The engine switch is off.


b.

for Automatic Transmission

The shift lever is in P.


c.

A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*) is performed.

HINT:

*: This is the lock/unlock operation with the mechanical key.



d.

Turn the steering wheel and check the steering condition.

OK:

Steering is locked.



Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

END (BODY ECU WAS DEFECTIVE)

NG (for Automatic Transmission)

15.READ VALUE USING GTS (SHIFT P SIGNAL)

NG (for Manual Transmission)

17.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
15.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal OK or NG ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


OK:

ON (shift lever in P) or OFF (shift lever not in P) appears on the screen according to the shift lever position.



Result:
Proceed to
OK
NG



OK

16.CHECK STEERING LOCK CONDITION

NG

20.INSPECT SHIFT LOCK CONTROL ECU (TRANSMISSION FLOOR SHIFT ASSEMBLY)
16.CHECK STEERING LOCK CONDITION
a.

The engine switch is off.


b.

The shift lever is in P.


c.

A door is opened or a door lock operation (door lock, wireless door lock or key-linked lock operation*) is performed.

HINT:

*: This is the lock/unlock operation with the mechanical key.



d.

Turn the steering wheel and check the steering condition.

OK:

Steering is locked.



Result:
Proceed to
OK
NG



OK

END (CONNECT CONNECTORS PROPERLY)

NG

17.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
17.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
a.

The steering is unlocked.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock Steering lock ECU (steering lock actuator assembly) lock confirmation status Set or Unset Set: Lock confirmed
Unset: Lock not confirmed
When Unset is displayed, the steering wheel is not locked.
Steering Unlock Steering lock ECU (steering lock actuator assembly) unlock confirmation status Set or Unset Set: Unlock confirmed
Unset: Unlock not confirmed
When Unset is displayed, the steering wheel is not unlocked (the engine cannot be started).
OK:

"Steering Lock" is "Unset" and "Steering Unlock" is "Set"



Result:
Proceed to
OK
NG



OK

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

18.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
19.READ VALUE USING GTS (LOCK REQUEST RECEIVE)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of opening any door with engine switch off and shift lever in P*
NG: Except above
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

*: for Automatic Transmission


Body Electrical > Entry&Start > Data List
Tester Display
Lock Request Receive
50003 125 68
OK:

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to off and opening a door with the shift lever in P (for Automatic Transmission), and OK is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

20.INSPECT SHIFT LOCK CONTROL ECU (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the I4 shift lock control ECU (transmission floor shift assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.


C327012C03
0.26,0.958 0.688,1.188 0.427,0.229 0.875,1.958 1.073,1.958 1.073,1.958 1.427,1.531 false 1.802,1.104 2.333,0.469 2.333,0.469 2.51,0.469 false 0.177,0.104 0.49,0.302 0.313,0.198 10 false *a 0.667,1.875 0.979,2.073 0.313,0.198 10 false P2 2.552,0.396 2.708,0.594 0.156,0.198 10 false E 0.427,1.01 0.74,1.208 0.313,0.198 10 false I4
*a Component without harness connected
(Shift Lock Control ECU (Transmission Floor Shift Assembly))


Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) tester probe → I4-11 (P2) Negative (-) tester probe → I4-3 (E) Shift lever in P 30k Ω or higher
Shift lever not in P Below 200 Ω


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

NG

REPLACE SHIFT LOCK CONTROL ECU

21.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (SHIFT LOCK CONTROL UNIT ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the I4 shift lock control ECU (transmission floor shift assembly) connector.


b.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
I4-11 (P2) - G16-8 (P) Always Below 1 Ω
I4-3 (E) - Body ground Always Below 1 Ω
I4-11 (P2) - Body ground Always 10 kΩ or higher
G16-8 (P) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR