Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0201960 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.

*1: for Automatic Transmission

*2: for Manual Transmission


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control
·

Stop Light Switch1*

·

Steering Unlock Switch

·

Power Supply Condition

·

IG Relay Monitor(Inside)

·

IG Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal*

·

Neutral SW/ Clutch SW

·

Starter Request Signal


Entry&Start
·

L Code Check

·

Engine Start Request

·

Immobiliser


Starting Control
·

Ignition

·

Starter SW

·

Shift Position P or N*


-

*: for Automatic Transmission


HINT:

If the brake pedal*1 or clutch pedal*2 is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal*1 or clutch pedal*2 to illuminate the stop lights increases.

*1: for Automatic Transmission

*2: for Manual Transmission



WIRING DIAGRAM

Refer to "SYSTEM DIAGRAM".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>SYSTEM DIAGRAM

C329192E02
2.74,3.031 3.833,3.385 1.094,0.354 10 false Stop Light Switch Assembly* 2.74,2.906 3.198,3.104 0.458,0.198 10 false A64 1.906,2.188 2.521,2.385 0.615,0.198 10 false STOP 0.563,2.042 1.385,2.271 0.823,0.229 10 false from Battery 3.458,2.313 3.615,2.51 0.156,0.198 10 false L 3.688,2.177 3.844,2.375 0.156,0.198 10 false 3 2.865,2.552 3.323,2.75 0.458,0.198 10 false GND 2.677,2.427 2.833,2.625 0.156,0.198 10 false 2 2.875,2.042 3.031,2.24 0.156,0.198 10 false B 2.677,1.917 2.833,2.115 0.156,0.198 10 false 7 3.104,1.271 3.563,1.469 0.458,0.198 10 false ECM 3.094,1.125 4.021,1.313 0.927,0.188 10 false G50 3.677,0.417 4.417,0.594 0.74,0.177 10 false 13 3.292,0.542 3.75,0.74 0.458,0.198 10 false STP 5.115,1.125 5.427,1.323 0.313,0.198 10 false A4 4.792,4.792 7.104,5.156 2.313,0.365 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly)* 4.781,4.646 5.552,4.844 0.771,0.198 10 false I4 5.156,2.833 5.615,3.031 0.458,0.198 10 false G16 5.156,2.969 6.688,3.333 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.104,1.26 6.656,1.615 1.552,0.354 10 false Skid Control ECU (Brake Actuator Assembly) 0.24,5.302 2.146,5.521 1.906,0.219 10 false *: for Automatic Transmission 5.427,2.302 6.042,2.5 0.615,0.198 10 false STP1 5.177,2.188 5.49,2.385 0.313,0.198 10 false 11 5.417,0.531 6.031,0.729 0.615,0.198 10 false STP2 5.427,4.031 5.885,4.229 0.458,0.198 10 false STP 5.229,3.938 5.385,4.135 0.156,0.198 10 false 6 5.24,0.406 5.396,0.604 0.156,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

·

If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.



Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Radio Wave Interference
Parameter Name Content
Operating Engine Switch / Key RF Signal Interference When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

Engine Start Inactive (brake system) (for Automatic Transmission)
Parameter Name Content
Operating Power Switch/brake or clutch no signal When the engine switch was turned on (IG) twice, there was no brake signal, and then the warning alarm sounded.

Engine Start Inactive (brake system) (for Manual Transmission)
Parameter Name Content
Operating Power Switch/brake or clutch no signal When the engine switch was turned on (IG) twice, there was no clutch signal, and then the warning alarm sounded.

Engine Start Inactive (radio wave interference) (for Automatic Transmission)
Parameter Name Content
Operating Power Switch/ Indoor oscillator LF Signal Interference When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.
Brake or Clutch Switch/Indoor oscillator LF Signal Interference When the brake switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

Engine Start Inactive (radio wave interference) (for Manual Transmission)
Parameter Name Content
Operating Power Switch/ Indoor oscillator LF Signal Interference When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.
Brake or Clutch Switch/Indoor oscillator LF Signal Interference When the clutch switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.

Engine Start Inactive (steering lock system)
Parameter Name Content
Operating Power Switch/steering lock detection Engine did not start because steering is lock status when engine switch was pushed.

PROCEDURE

1.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

2.READ VALUE USING GTS (KEY LOW BATTERY)

B

18.INSPECT TRANSMITTER BATTERY

C

2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
Body Electrical > Entry&Start > Data List
Tester Display
Key Low Battery
50003 125 23

OK:

"No" is displayed in the Data List.


Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Starting Control > Trouble Codes
50001 221
Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
DTCs are not output A
Smart entry and start system (for Start Function) DTCs are output B



A

4.CHECK ENGINE CRANK

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

4.CHECK ENGINE CRANK
a.

Get into the vehicle while carrying the electrical key transmitter.


b.

for Automatic Transmission

Move the shift lever to P.


c.

Depress the brake pedal*1 or clutch pedal*2.

*1: for Automatic Transmission

*2: for Manual Transmission



d.

Press the engine switch and check that the engine cranks.


Result:
Result Proceed to
Engine cranks, but there is no initial combustion or engine is difficult to start A
Engine does not cranks B



A

B

5.CHECK ENGINE SWITCH CONDITION
5.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission

Move the shift lever to P.


c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for Automatic Transmission

*2: for Manual Transmission



Result:
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

6.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SWITCH/ CLUTCH SW)

B

C

D

6.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SWITCH/ CLUTCH SW)
a.

for Automatic Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.




b.

for Manual Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
OK:

The item in the Data List changes when the clutch pedal is depressed and released.




Result:
Proceed to
OK (for Automatic Transmission)
OK (for Manual Transmission)
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK (for Automatic Transmission)

7.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

OK (for Manual Transmission)

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG (for Automatic Transmission)

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG (for Manual Transmission)

26.INSPECT CLUTCH START SWITCH ASSEMBLY
7.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P and N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever not in P or N
·

Use this item to determine whether the park/neutral start switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral start switch assembly malfunction, "OFF" is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Park/neutral position switch status ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2

OK:

The item in the Data List changes according to the shift position.


Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status ON or OFF
for Automatic Transmission

ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second has elapsed, the engine switch is released


for Manual Transmission

ON: With the clutch pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second has elapsed, the engine switch is released


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the smart warning light is illuminated in green on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (STARTER SW)

NG

33.CHECK STEERING LOCK SYSTEM
9.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P*1, press the engine switch while depressing the brake pedal*1 or clutch pedal*2 and confirm that the Data List item changes.

*1: for Automatic Transmission

*2: for Manual Transmission


Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request ON or OFF ON: Starter operation requested
OFF: Starter operation not requested
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The Data List item changes.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (STARTER RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.READ VALUE USING GTS (STARTER RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Relay Starter relay voltage monitor ON or OFF ON: ST NO. 1 relay on
OFF: ST NO. 1 relay off
OFF is displayed when the engine cannot crank.
Body Electrical > Starting Control > Data List
Tester Display
Starter Relay
50003 221 3

Result:
Proceed to
OK
NG



OK

11.CHECK CONNECTOR CONNECTION CONDITION

NG

14.INSPECT ST NO. 1 RELAY
11.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Remove the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL


b.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C22 park/neutral position switch assembly connector.


c.

Disconnect the G49 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - C22-4 (B) Always Below 1 Ω
G17-16 (STAR) or C22-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT ST NO. 1 RELAY
a.

Remove the ST NO. 1 relay.



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST NO. 1 RELAY

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B342621C06
1.469,0.281 1.969,0.542 0.5,0.26 2.25,1.75 2.563,1.229 true 2.875,1.74 2.698,1.063 true 2.76,1.802 3.188,1.969 0.427,0.167 10 false STAR 2.104,1.802 2.563,2 0.458,0.198 10 false STA 1.594,0.333 2.052,0.531 0.458,0.198 10 false G17 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G49 ECM connector.


c.

for Automatic Transmission

Move the shift lever to P or N.


d.

for Manual Transmission

Clutch pedal depressed.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - Body ground 20°C (68°F) 93.75 to 136.36 Ω
G17-37 (STA) - Body ground



Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

16.INSPECT STARTER ASSEMBLY

NG (for Automatic Transmission)

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

NG (for Manual Transmission)

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
16.INSPECT STARTER ASSEMBLY
a.

Remove the starter assembly.

for 1GD-FTV (for 2.0 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL

for 1GD-FTV (for 2.2 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL


b.

Inspect the starter assembly.

for 1GD-FTV (for 2.0 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>INSPECTION

for 1GD-FTV (for 2.2 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST NO. 1 RELAY)

NG

REPLACE STARTER ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST NO. 1 RELAY)
a.

Remove the starter assembly from the vehicle to perform an inspection.

for 1GD-FTV (for 2.0 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.0 kW Type)>REMOVAL

for 1GD-FTV (for 2.2 kw Type): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for 2.2 kW Type)>REMOVAL


b.

Remove the ST NO. 1 relay.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-1 (B) - Body ground Always 11 to 14 V
ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 3 - C26-1 (ST) Always Below 1 Ω
ST NO. 1 relay terminal 3 or C26-1 (ST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

19.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G50 ECM connector.


b.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A64 stop light switch assembly connector.


e.

Disconnect the I4 shift lock control ECU (transmission floor shift assembly) connector.


f.
E233306C33
1.427,0.25 1.927,0.5 0.5,0.25 1.219,1.74 1.385,1.188 true 1.688,1.74 1.51,1.198 true 2.5,1.75 2.25,1.167 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.094,1.792 1.552,1.99 0.458,0.198 10 false GND 1.719,1.781 1.927,1.969 0.208,0.188 10 false L 2.49,1.781 2.646,1.979 0.156,0.198 10 false B 1.563,0.302 1.875,0.5 0.313,0.198 10 false A64
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-7 (B) - Body ground Always 11 to 14 V



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-11 (STP1) - A64-3 (L) Always Below 1 Ω
G16-11 (STP1) or A64-3 (L) - Body ground Always 10 kΩ or higher
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C22 park/neutral position switch connector.


c.

Disconnect the G49 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - C22-4 (B) Always Below 1 Ω
G17-16 (STAR) or C22-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)
a.

Disconnect the C22 park/neutral position switch connector.


b.

Remove the ST NO. 1 relay.


c.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G49 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (L) - ST NO. 1 relay terminal 2 Always Below 1 Ω
C22-5 (L) or ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-37 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
G17-37 (STA) or ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

25.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

26.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B2 clutch start switch assembly connector.


c.

Disconnect the G49 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - B2-2 Always Below 1 Ω
G17-16 (STAR) or B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B2 clutch start switch assembly connector.


c.

Disconnect the G49 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - B2-2 Always Below 1 Ω
G17-16 (STAR) or B2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the B2 clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay.


c.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G49 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B2-1 - ST NO. 1 relay terminal 2 Always Below 1 Ω
B2-1 or ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST NO. 1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-37 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
G17-37 (STA) or ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

32.CHECK CONNECTOR CONNECTION CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK CONNECTOR CONNECTION CONDITION
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


c.

Press the engine switch and check that the engine starts.

OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

CONNECT SECURELY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

33.CHECK STEERING LOCK SYSTEM
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

34.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

NG

GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE)

34.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission

Move the shift lever to P.


c.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:

It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG