Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2015.08–2016.01
RM3270E _51 Engine / Hybrid System _041679 CRUISE CONTROL _0199359 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

ECM

·

Harness or connector



WIRING DIAGRAM

C327402E03
1.917,0.979 3.063,1.281 1.146,0.302 10 false from IG Circuit 1.917,0.313 2.74,0.604 0.823,0.292 10 false from Battery 1.802,3 2.417,3.198 0.615,0.198 10 false STOP 2.771,2.052 2.927,2.25 0.156,0.198 10 false B 2.771,2.719 2.927,2.917 0.156,0.198 10 false B 2.594,2.052 2.75,2.25 0.156,0.198 10 false 6 2.594,2.719 2.75,2.917 0.156,0.198 10 false 7 2.583,3.302 2.74,3.5 0.156,0.198 10 false 2 2.771,3.531 3.229,3.729 0.458,0.198 10 false GND 4.51,2.052 4.667,2.25 0.156,0.198 10 false L 4.51,2.719 4.667,2.917 0.156,0.198 10 false L 4.677,2.052 4.833,2.25 0.156,0.198 10 false 5 4.677,2.719 4.833,2.917 0.156,0.198 10 false 3 2.5,3.917 2.958,4.115 0.458,0.198 10 false A64 2.833,3.958 4.625,4.167 1.792,0.208 10 false Stop Light Switch Assembly 5.313,2.042 5.625,2.24 0.313,0.198 10 false 12 5.313,2.708 5.625,2.906 0.313,0.198 10 false 13 5.583,2.302 5.948,2.479 0.365,0.177 10 false ST1- 5.583,2.969 6.042,3.167 0.458,0.198 10 false STP 5.542,3.75 6,3.948 0.458,0.198 10 false G50 6.042,3.833 6.5,4.031 0.458,0.198 10 false ECM 1.677,2.333 2.458,2.531 0.781,0.198 10 false IG2 NO. 3 5.583,6.781 6.042,6.979 0.458,0.198 10 false STP2 5.583,4.917 6.042,5.115 0.458,0.198 10 false STP1 3.146,4.896 3.604,5.094 0.458,0.198 10 false STP 5.417,5.458 6.917,6 1.5,0.542 10 false Certification ECU (Smart Key ECU Assembly)*1 3.625,4.917 4,5.083 0.375,0.167 10 false I4 3.99,4.917 4.365,5.083 0.375,0.167 10 false I6 5.208,5.281 5.583,5.448 0.375,0.167 10 false G16 2.104,5.375 3.771,5.583 1.667,0.208 10 false Shift Lock Control ECU*3 5.427,7.25 7,7.969 1.573,0.719 10 false Skid Control ECU (Brake Actuator Assembly) 5.24,7.104 5.615,7.271 0.375,0.167 10 false A4 0.583,6.708 3.438,6.885 2.854,0.177 10 false *1: w/ Smart Entry and Start System 0.583,7.198 4.302,7.406 3.719,0.208 10 false *2: w/o Smart Entry and Start System 3.583,5.177 3.896,5.375 0.313,0.198 10 false *1 3.958,5.177 4.271,5.375 0.313,0.198 10 false *2 3.625,4.698 3.781,4.896 0.156,0.198 10 false 6 4,4.698 4.156,4.896 0.156,0.198 10 false 4 5.313,4.802 5.625,5 0.313,0.198 10 false 11 5.385,6.656 5.542,6.854 0.156,0.198 10 false 7 0.583,7.708 5.167,7.906 4.583,0.198 10 false *3: for Automatic Transmission

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270087C04
1.604,0.167 2,0.417 0.396,0.25 1.417,1.167 0.917,1.75 0.917,1.75 0.75,1.75 true 2.167,1.167 2.167,1.75 true 2.5,1.167 2.833,1.75 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.417,1.667 0.875,1.865 0.458,0.198 10 false GND 2.125,1.76 2.281,1.958 0.156,0.198 10 false B 2.844,1.75 3,1.948 0.156,0.198 10 false B 1.688,0.219 2.021,0.385 0.333,0.167 10 false A64
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) -Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-6 (B) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
A64-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

2.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G50 ECM connector.


b.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A64 stop light switch assembly connector.


d.

for Automatic Transmission:

i.

w/ Smart Entry and Start System

Disconnect the I4 shift lock control ECU connector.


ii.

w/o Smart Entry and Start System

Disconnect the I6 shift lock control ECU connector.



e.

w/ Smart Entry and Start System:

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G50-12 (ST1-) - A64-5 (L) Always Below 1 Ω
G50-13 (STP) - A64-3 (L) Always Below 1 Ω
G50-12 (ST1-) or A64-5 (L) - Body ground Always 10 kΩ or higher
G50-13 (STP) or A64-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT SWITCH OUTPUT VOLTAGE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

3.CHECK STOP LIGHT SWITCH OUTPUT VOLTAGE
a.
C326505C06
1.5,0.26 1.917,0.5 0.417,0.24 1.635,1.354 0.667,1.667 true 2.75,1.667 1.792,1.354 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 1.583,0.302 2.042,0.5 0.458,0.198 10 false G50 0.469,1.698 1.083,1.896 0.615,0.198 10 false ST1- 2.688,1.688 3.146,1.885 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G50-12 (ST1-) - Body ground Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
G50-13 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY