Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.
71051A
1.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
While rotating the part in installation direction (1) shown in the illustration, attach the hook.
Push in Installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly RH.
82191
2.INSTALL FRONT SEAT WIRE RH
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
Connect the 3 connectors.
Attach the wire harness clamp and connector clamp.
71537G
3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in installation direction (1) shown in the illustration to attach the guide.
While expanding the part in installation direction (2) shown in the illustration, attach the claw.
Install the front seat cushion edge protector RH with the screw.
71538B
4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Use the same procedure as for the RH side.
71873
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the guide in the installation direction (1) shown in the illustration.
Push in installation direction (2) shown in the illustration to attach the clip.
|
Install in this Direction |
Push in the guide in the installation direction shown in the illustration.
Install the front seat lower cushion shield RH with the screw.
71874
6.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
Use the same procedure as for the RH side.
7.INSTALL SEAT COVER WIRE
Remove the seat cover wire.
There are service parts available for wires of 1000 mm or longer and formed wires.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.
Refer to the precautions when creating a wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 170 mm (6.70 in.) |
| B | 150 mm (5.91 in.) |
| C | 230 mm (9.06 in.) |
| D | 270 mm (10.63 in.) |
| E | 290 mm (11.42 in.) |
The dimensions shown in the illustration are the length.
71071S
8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
As shown in the illustration, fix all of the cover seam allowances in the same direction.
Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.
Do not dirty or damage the separate type front seat cushion cover.
Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.
| *1 | Hog Ring Pliers | - | - |
9.INSTALL SEAT CUSHION COVER WITH PAD
While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to attach the seat cushion cover with pad.
71587B
10.INSTALL FRONT SEATBACK EDGE PROTECTOR
Attach the claw to Install the 2 front seatback edge protectors.
71053S
11.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly RH.
Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly RH.
Push in installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly RH.
Attach the claw and install the 2 front seatback edge protectors.
71759D
12.INSTALL FRONT NO. 2 SEATBACK HOOK
|
Install in this Direction |
Push up installation direction shown in the illustration to attach the claw and install the 2 front No. 2 seatback hooks.
73910A
13.INSTALL FRONT SEAT AIRBAG ASSEMBLY RH
8219A
14.INSTALL FRONT SEAT NO. 2 WIRE RH
Connect the connector.
Attach the wire harness clamp and install the front seat No. 2 wire RH.
15.INSTALL SEAT COVER WIRE
Install the seat cover wire.
There are service parts available for wires of 1000 mm or longer and formed wires.
When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.
Refer to the precautions when creating a wire.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION
| A | 200 mm (7.87 in.) |
| B | 420 mm (1.38 ft.) |
The dimensions shown in the illustration are the length.
71073S
16.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.
As shown in the illustration, fix all of the cover seam allowances in the same direction.
Set the separate type front seatback cover.
Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.
Do not dirty or damage the separate type front seatback cover.
Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
17.INSTALL SEATBACK COVER WITH PAD
|
Install in this Direction |
Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.
w/ Front Seat Side Airbag:
| *1 | J Hook A |
| *2 | J Hook B |
|
Install in this Direction |
Push in installation direction shown in the illustration to attach the J hook A and J hook B.
| *1 | J Hook B (J Hook A and J Hook B) |
| *2 | J Hook C |
|
Install in this Direction |
Push in installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.
Install the new rivet to J hook B.
| *A | for LH seat | *B | for RH seat |
| *1 | J Hook A | *2 | J Hook B |
Place your hand at the position shown in the illustration and push in installation direction to attach the J hook B.
| *1 | J Hook A | *2 | J Hook B |
| *3 | J Hook C | - | - |
|
Place Hand Here |
|
Install in this Direction |
71931
18.INSTALL FRONT SEAT HEADREST SUPPORT
|
Install in this Direction |
Attach the claw and install the 2 front seat headrest supports.
|
Install in this Direction |
Pull up installation direction shown in the illustration to attach the guide to the 2 straps.
|
Install in this Direction |
Close the fasteners as shown in the illustration.
| *A | w/ Side Airbag System |
| *B | w/o Side Airbag System |
|
Install in this Direction |
Pass the wire harness through the opening in the back cover.
Using hog ring pliers, install 5 new hog rings.
| *1 | Hog Ring Pliers | - | - |
| *a | Cutout | - | - |
71759C
19.INSTALL FRONT NO. 1 SEATBACK HOOK
Attach the claw and install the front No. 1 seatback hook.
71875E
20.INSTALL RECLINING ADJUSTER INSIDE COVER RH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push down to attach the guide installation direction (1) shown in the illustration.
Rotate the part in installation direction (2) shown in the illustration to install the reclining adjuster inside cover RH.
71875G
21.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Use the same procedure as for the RH side.
71013S
22.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH
| *A | LH Side |
| *B | RH Side |
Install the 4 bolts and front seatback frame sub-assembly RH.
| *A | LH Side |
| *B | RH Side |
| *1 | Separate Type Front Seat Cushion Cover |
Attach the hook.
Connect the Connector and attach the guide.
w/ Front Seat Side Airbag:
Attach the wire harness clamp.
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
Attach the wire harness clamp and connector clamp.
Install the band in the position shown in the illustration.
73230
23.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
71861
24.INSTALL FRONT SEAT INNER CUSHION SHIELD RH
|
Install in this Direction |
Push in installation direction shown in the illustration to attach the claw and guide.
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield RH.
84922B
25.INSTALL FRONT POWER SEAT SWITCH RH
71811D
26.INSTALL FRONT SEAT CUSHION SHIELD RH
| *1 | Wire Harness Clamp |
| *2 | Connector Clamp |
| *3 | Hook A |
| *4 | Hook B |
Attach the claw.
Attach the hook B.
Attach the wire harness clamp and connector clamp.
Connect the 2 connectors.
Attach the hook A.
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the guide, claw and clip.
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the clip and guide.
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the claw to install the front seat cushion shield RH.
71867A
27.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH
|
Install in this Direction |
Push in installation direction shown in the illustration to install the guide.
Install the screw and front seat inner No. 1 cushion shield RH.
84921J
28.INSTALL POWER SEAT SWITCH KNOB RH (for Reclining)
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.
84921C
29.INSTALL POWER SEAT SWITCH KNOB RH (for Slide and Vertical, Lifter)
|
Install in this Direction |
Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.
71848A
30.INSTALL SEAT ADJUSTER COVER CAP RH
|
Install in this Direction |
Push in installation direction shown in the illustration to install the 2 seat adjuster cover caps RH.
71910A
31.INSTALL FRONT SEAT HEADREST ASSEMBLY
|
Apply Silicon |
Apply silicon lubricant in this range.
Install the front seat headrest assembly.