Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3270E _51 Engine / Hybrid System _041671 1GD-FTV ENGINE CONTROL _0203615 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0100  Mass Air Flow Circuit  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

A332068C01
5.479,1.865 6.344,2.813 6.344,2.813 6.573,2.813 true 5.823,2.896 6.156,3.292 6.156,3.292 6.385,3.292 true 2.719,1.542 3.021,1.698 3.021,1.698 3.25,1.698 true 2.323,0.844 2.896,1.063 2.896,1.063 3.125,1.063 true 1.5,1.042 1.698,1.042 1.698,1.042 2.094,0.833 true 1.313,1.74 1.51,1.74 1.51,1.74 1.792,1.51 true 3.104,1.438 3.219,1.521 3.219,1.521 3.448,1.521 true 4.542,2.427 4.792,2.427 4.792,2.427 5.25,2.219 true 6.615,2.74 6.927,2.938 0.313,0.198 10 false *a 6.438,3.219 6.75,3.417 0.313,0.198 10 false *q 3.167,1 3.479,1.198 0.313,0.198 10 false *c 1.323,0.979 1.635,1.177 0.313,0.198 10 false *d 3.271,1.646 3.583,1.844 0.313,0.198 10 false *f 3.49,1.458 3.802,1.656 0.313,0.198 10 false *e 1.156,1.667 1.469,1.865 0.313,0.198 10 false *g 4.135,2.688 4.448,2.885 0.313,0.198 10 false 5V 4.135,3.344 4.448,3.542 0.313,0.198 10 false FG 4.135,4.313 4.604,4.552 0.469,0.24 10 false E2G 0.802,3.875 1.115,4.073 0.313,0.198 10 false *c 1.188,3.885 1.5,4.083 0.313,0.198 10 false *d 1.729,3.896 2.042,4.094 0.313,0.198 10 false *h 2.458,3.458 2.771,3.656 0.313,0.198 10 false *j 2.771,3.458 3.083,3.656 0.313,0.198 10 false *k 2.448,4.104 2.76,4.302 0.313,0.198 10 false *l 2.771,4.094 3.083,4.292 0.313,0.198 10 false *m 3.521,3.917 3.833,4.115 0.313,0.198 10 false *i 3.448,3.313 3.76,3.51 0.313,0.198 10 false *n 4.635,0.51 4.948,0.708 0.313,0.198 10 false *1 1.229,4.51 1.573,4.646 0.344,0.135 10 false *o 2.583,4.521 2.896,4.656 0.313,0.135 10 false *p 4.365,2.354 4.677,2.552 0.313,0.198 10 false *b
*1 Mass Air Flow Meter Sub-assembly - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Intake Air Thermistor 1
*i Intake Air Thermistor 2 *j Temperature Sensor (Before Heater) 1
*k Temperature Sensor (After Heater) 2 *l Temperature Sensor (After Heater) 1
*m Temperature Sensor (Before Heater) 2 *n Control Circuit
*o Heater Control Bridge Circuit *p Temperature Sensor Bridge Circuit
*q Air Flow - -


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass Air Flow Circuit Mass air flow meter sub-assembly signal frequency is less than 0.1 kHz with the engine speed at 400 rpm or more for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0100 MAF

HINT:

If DTC P0100 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

·

Combustion noise worsens




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0100 3 seconds or more after engine is started

WIRING DIAGRAM

A348535E05
2.198,2.052 2.656,2.25 0.458,0.198 10 false 2 1.906,0.656 2.365,0.854 0.458,0.198 10 false 5V 1.885,1.24 2.344,1.438 0.458,0.198 10 false FG 1.813,1.833 2.271,2.031 0.458,0.198 10 false E2G 2.208,2.625 2.667,2.823 0.458,0.198 10 false 4 2.188,1.438 2.646,1.635 0.458,0.198 10 false 1 2.188,0.896 2.646,1.094 0.458,0.198 10 false 3 1.823,2.375 2.281,2.573 0.458,0.198 10 false THA 0.656,3.198 1.115,3.396 0.458,0.198 10 false A29 0.635,3.375 2.99,3.615 2.354,0.24 10 false Mass Air Flow Meter Sub-assembly 4.938,0.885 5.396,1.083 0.458,0.198 10 false 25 4.917,1.469 5.375,1.667 0.458,0.198 10 false 33 4.927,2.063 5.385,2.26 0.458,0.198 10 false 24 4.938,2.615 5.396,2.813 0.458,0.198 10 false 32 5.552,3.208 6.01,3.406 0.458,0.198 10 false C39 5.583,3.375 6.042,3.573 0.458,0.198 10 false ECM 5.188,1.25 5.646,1.448 0.458,0.198 10 false VG 5.177,1.823 5.635,2.021 0.458,0.198 10 false EVG 5.177,2.385 5.635,2.583 0.458,0.198 10 false THA 5.188,0.667 5.646,0.865 0.458,0.198 10 false VCVG

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
A332051C18
0.25,1.917 0.667,2.167 0.417,0.25 2.156,3.104 1.823,2.406 true 1.104,3.094 1.375,2.396 true 1.583,3.094 1.594,2.396 true 0.208,0.177 0.521,0.333 0.313,0.156 10 false *a 2.135,3.135 2.479,3.354 0.344,0.219 10 false 5V 0.333,1.969 0.792,2.167 0.458,0.198 10 false A29 0.99,3.135 1.333,3.354 0.344,0.219 10 false FG 1.49,3.146 1.833,3.365 0.344,0.219 10 false E2G
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-3 (5V) - Body ground Ignition switch ON 4.8 to 5.2 V
A29-1 (FG) - A29-2 (E2G) Ignition switch ON 4.8 to 5.2 V



d.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0100 IS OUTPUT AGAIN)
3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0100 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and wait for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0100 is output A
DTCs are not output B




A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-3 (5V) - C39-25 (VCVG) Always Below 1 Ω
A29-1 (FG) - C39-33 (VG) Always Below 1 Ω
A29-2 (E2G) - C39-24 (EVG) Always Below 1 Ω
A29-3 (5V) or C39-25 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
A29-1 (FG) or C39-33 (VG) - Body ground and other terminals Always 10 kΩ or higher
A29-2 (E2G) or C39-24 (EVG) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the mass air flow meter sub-assembly connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and wait for 3 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED