Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3270E _51 Engine / Hybrid System _041671 1GD-FTV ENGINE CONTROL _0203615 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2080  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1  P2084  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2  P242B  Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3  


DESCRIPTION

Refer to DTC P0545.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>P0545

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2080 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1 The change in the exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
·

Exhaust gas temperature sensor

·

ECM (soak timer)


Comes on DTC stored
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 The change in the No. 2 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
·

No. 2 exhaust gas temperature sensor

·

ECM (soak timer)


Comes on DTC stored
P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3 The change in the No. 3 exhaust temperature sensors from before the engine is started (after leaving the vehicle alone for 10 hours) and after driving for a fixed amount of time (approximately 15 minutes) is small.
(2 trip detection logic)
·

No. 3 exhaust gas temperature sensor

·

ECM (soak timer)


Comes on DTC stored

Related Data List
DTC No. Data List
P2080
·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3


P2084
P242B

HINT:
·

Sensor 1 represents the sensor located upstream of the DOC catalytic converter.

·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

·

Sensor 3 represents the sensor located downstream of the DPF catalytic converter.

·

If DTC P2080, P2084 and/or P242B is stored, the following symptoms may appear:

·

White smoke




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2080 Check the exhaust gas temperature after leaving the vehicle for 1 to 2 hours and after driving*
*: Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.
P2084
P242B

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2080, P2084 AND P242B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P2080, P2084 or P242B is output A
DTC P2080, P2084 or P242B and other DTCs are output B




A

2.READ VALUE USING GTS (EXHAUST TEMPERATURE)

B

2.READ VALUE USING GTS (EXHAUST TEMPERATURE)
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.


e.

Record the exhaust temperature displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 234 858,859,860

Result:
Proceed to
NEXT



NEXT

3.INSPECT EXHAUST GAS TEMPERATURE SENSOR
3.INSPECT EXHAUST GAS TEMPERATURE SENSOR
a.

Drive the vehicle for 5 minutes or more at a speed of 50 km/h (31.1 mph) or more.


b.

Stop the vehicle.


c.

Connect the GTS to the DLC3.


d.

Enter the following menus: Powertrain / Engine and ECT/ Data List / Exhaust Temperature B1S1, ExhaustTemperature B1S2 and Exhaust Temperature B1S3.


e.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 234 858,859,860
Result:
Result Proceed to
Difference between Exhaust Temperature B1S1 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S1 checked after driving is within +/-15°C (27°F) A
Difference between Exhaust Temperature B1S2 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S2 checked after driving is within +/-15°C (27°F)
Difference between Exhaust Temperature B1S3 recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and Exhaust Temperature B1S3 checked after driving is within +/-15°C (27°F)
Difference between exhaust temperature recorded in "READ VALUE USING GTS (EXHAUST TEMPERATURE)" and exhaust temperature checked after driving is equal to or greater than +/- 15°C (27°F) B




A

4.REPLACE EXHAUST GAS TEMPERATURE SENSOR

B

6.REPLACE ECM
4.REPLACE EXHAUST GAS TEMPERATURE SENSOR
HINT:

Replace the exhaust temperature sensor that changed a small amount in "INSPECT EXHAUST GAS TEMPERATURE SENSOR".


a.

b.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


c.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Exhaust / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.


e.

Drive the vehicle for 5 minutes or more at a speed of 50km/h (31.1 mph) or more.


f.

Stop the vehicle.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.


i.

Check the exhaust temperature after leaving the vehicle for 1 to 2 hours and after driving.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 234 858,859,860
Standard:

+/-15°C(27°F) or more



Result:
Proceed to
NEXT



NEXT

END

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED