Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ DPF)
RM3270E _51 Engine / Hybrid System _041671 1GD-FTV ENGINE CONTROL _0203615 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2263  Turbo/Super Charger Boost System Performance  


DESCRIPTION

After the ignition switch is turned off, the ECM performs nozzle vane plate soot removal control (current opening angle→fully opened→fully closed). Monitor the motor drive current value while these opening and closing operations are performed. If the value exceeds the threshold, it can be determined that movement is abnormal. If the system judges that abnormal movements have occurred twice, this DTC is stored and the go to service warning light illuminates the next time the ignition switch is turned to ON.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2263 Turbo/Super Charger Boost System Performance During soot removal control of the nozzle vane plate after the ignition switch is turned off, DC motor operation current exceeds the threshold.
(2 trip detection logic)
Abnormality in sliding movement of turbocharger nozzle vane plate -*
*: Go to service warning light illuminates in combination meter
DTC stored

READINESS MONITOR DRIVE PATTERN

DTC No. DTC Detection Drive Pattern
P2263 Turn the ignition switch off, and then perform turbocharger nozzle vane plate soot removal control.

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (P2263)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read DTCs.

Result:
Result Proceed to
P2263 is output A
P2263 and other DTCs are output B




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)

B

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VN TURBO CLEANING)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature is 77°C (170°F) or higher with all the accessories switched off .


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Cleaning.


e.

Perform the Active Test.

HINT:
·

VN turbo cleaning finishes 20 minutes after the speed increases.

·

If actions such as depressing the accelerator pedal or operating the shift lever are performed, cleaning control is stopped. If this occurs, it is necessary to perform the procedure again.




Result:
Proceed to
NEXT



NEXT

3.INSPECT COMBINATION METER DISPLAY (WARNING DISPLAY)
3.INSPECT COMBINATION METER DISPLAY (WARNING DISPLAY)
a.

Turn the ignition switch off and wait for at least 30seconds.


b.

Turn the ignition switch ON.


c.

Check the combination meter assembly.

Result:
Result Proceed to
Go to service warning light illuminates in combination meter A
Go to service warning light does not illuminate in combination meter B




A

4.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch off and wait for at least 30seconds.


b.

Turn the ignition switch ON.


c.

Check that the go to service warning light does not illuminate in the combination meter.


d.

Connect the GTS to the DLC3.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.

Powertrain > Engine > Clear DTCs
50002 234

g.

Clear the DTC.


Result:
Proceed to
NEXT



NEXT

END