Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0205065 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Idle Up Switch Circuit  


DESCRIPTION

When the idle up switch is pushed, the air conditioning amplifier assembly outputs the engine idle up signal. If engine idle up does not occur when the idle up switch is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E322900E04
5.417,0.885 6.031,1.083 0.615,0.198 10 false SWVC 5.188,0.885 5.406,1.083 0.219,0.198 10 false 2 4.583,0.885 4.802,1.083 0.219,0.198 10 false 3 4.354,0.885 4.563,1.083 0.208,0.198 10 false E 2.958,0.885 3.333,1.083 0.375,0.198 10 false SW 2.75,0.885 2.969,1.083 0.219,0.198 10 false 6 3.229,1.302 3.604,1.5 0.375,0.198 10 false G130 3.25,1.469 4.25,1.667 1,0.198 10 false Idle Up Switch 5.26,1.74 5.708,1.938 0.448,0.198 10 false G131 5.271,1.896 6.833,2.427 1.563,0.531 10 false Air Conditioning Amplifier Assembly 2.146,1.146 2.854,1.313 0.708,0.167 10 false IG1 NO.4 0.208,0.979 1.615,1.344 1.406,0.365 10 false from Ignition Switch*1, IG1 NO.1 Relay*2 0.135,2.167 3.021,2.438 2.885,0.271 10 false *1: w/o Smart Entry and Start System 0.135,2.448 3.021,2.719 2.885,0.271 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (IDLE UP/PWR HEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IDLE UP/PWR HEAT Switch Idle up switch ON or OFF ON: Idle up switch on
OFF: Idle up switch off
-
Body Electrical > Air Conditioner > Data List
Tester Display
IDLE UP/PWR HEAT Switch
50003 121 173
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - BATTERY)
2.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - BATTERY)
a.
E322901C04
1.458,0.26 1.958,0.51 0.5,0.25 1.979,1.417 2.229,1.833 2.229,1.833 2.563,1.833 true 0.031,0.052 0.344,0.25 0.313,0.198 10 false *a 2.615,1.74 2.927,1.938 0.313,0.198 10 false SW 1.542,0.302 1.99,0.479 0.448,0.177 10 false G130
*a Front view of wire harness connector
(to Idle Up Switch)


Disconnect the idle up switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G130-6 (SW) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT IDLE UP SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT IDLE UP SWITCH


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G130 idle up switch connector.


b.

Disconnect the G131 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-3 (E) - G131-2 (SWVC) Always Below 1 Ω
G130-3 (E) or G131-2 (SWVC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR