When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
17111
1.INSTALL INTAKE MANIFOLD
| *a | Protrusion |
Install a new gasket to the cylinder head sub-assembly.
Install the gasket with the protrusion the rear side of the vehicle as shown in the illustration.
Temporarily install the intake manifold with the 7 bolts and 2 nuts.
|
Bolt |
|
Nut |
Tighten the 7 bolts and 2 nuts in the order shown in the illustration.
w/o DPF:
Connect the vacuum hose assembly to the vacuum transmitting pipe sub-assembly.
Connect the wire harness bracket with the bolt.
25804
2.INSTALL VACUUM CONTROL VALVE SET
Install the vacuum control valve set with bolt to the cylinder head sub-assembly.
Connect the 2 vacuum hoses to the vacuum control valve set and vacuum transmitting pipe sub-assembly.
Connect the wire harness clamp and vacuum control valve set connector.
23770
3.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
Install the No. 2 nozzle leakage pipe assembly with the 2 bolts.
Connect the No. 6 fuel hose to the No. 3 nozzle leakage pipe assembly and slide the clamp to secure the hoses.
Install the No. 4 fuel hose and No. 5 fuel hose to the No. 2 nozzle leakage pipe assembly, and slide the 4 clamps to secure the hose.
23804C
4.INSTALL FUEL INLET PIPE SUB-ASSEMBLY
When replacing the fuel supply pump assembly, it is necessary to replace the fuel inlet pipe sub-assembly, No. 1 injection pipe clamp and No. 2 injection pipe clamp with a new one.
Keep the fuel inlet pipe sub-assembly free of foreign matter.
Temporarily install the fuel inlet pipe sub-assembly.
Install new No. 1 injection pipe clamp and No. 2 injection pipe clamp with the 2 bolts.
Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
When using a union nut wrench (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 31 N*m (316 kgf*cm, 23 ft.*lbf)
| *a | Torque Wrench Fulcrum Length |
Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 41 N*m (418 kgf*cm, 30 ft.*lbf)
17118
5.INSTALL MANIFOLD STAY
Install the manifold stay with the 2 bolts.
Install the wiring harness clamp bracket with the bolt.
23815D
6.INSTALL NO. 3 FUEL PIPE
Temporarily install the No. 3 fuel pipe and 2 new gaskets with the union bolt and supply pump hollow screw.
Tighten the union bolt and supply pump hollow screw.
Install the 2 fuel pipe clamps to the No. 3 fuel pipe and fuel filter.
| *a | Paint Mark |
| *b | 0 to 2 mm (0 to 0.0787 in.) |
Install the 2 fuel pipe clamps to the No. 3 fuel pipe and fuel filter.
Be careful that the fuel pipe clamp and No. 4 fuel pipe sub-assembly do not interfere with each other.
Make sure the fuel pipe clamp is oriented as shown in the illustration.
23804D
7.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY
Temporarily install the No. 4 fuel pipe sub-assembly and 2 new gaskets with the 2 union bolts and bolt.
|
Union Bolt |
|
Bolt |
Tighten the 2 union bolts and bolts in the order shown in the illustration.
Connect the No. 4 fuel pipe sub-assembly to the No. 1 fuel pipe.
Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>PRECAUTION
8.INSTALL WIRING HARNESS CLAMP BRACKET
Install the wiring harness clamp bracket with the bolt.
Attach the 2 wire harness clamps.
Connect the diesel throttle body assembly connector and pre-stroke control valve connector.
23812D
9.INSTALL NO. 2 FUEL PIPE
Connect the No. 2 fuel pipe and with the bolt.
11409
10.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Install the engine oil level dipstick guide with the bolt.
Connect the vacuum hose to the intake manifold.
Install the engine oil level dipstick.
25800
11.INSTALL EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)
13.ADD ENGINE COOLANT
14.BLEED AIR FROM FUEL SYSTEM
15.INSPECT FOR FUEL LEAK
16.INSPECT FOR COOLANT LEAK
17.INSPECT FOR OIL LEAK
18.INSPECT ENGINE OIL LEVEL