Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205696 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Power Back Door cannot be Opened or Closed Using the Back Door Control Switch  


DESCRIPTION

When the power back door cannot be closed using the back door control switch, either of the following may be malfunctioning: 1) back door control switch circuit or 2) multiplex network door ECU.

WIRING DIAGRAM

B411134E01
5.854,1.083 6.313,1.281 0.458,0.198 10 false CPU 1.417,1.49 1.875,1.688 0.458,0.198 10 false V20 4.479,2.031 4.938,2.229 0.458,0.198 10 false V12 4.51,2.219 6.385,2.438 1.875,0.219 10 false Multiplex Network Door ECU 4.531,1.208 5.146,1.406 0.615,0.198 10 false BDDN 4.313,0.927 4.469,1.125 0.156,0.198 10 false 4 3.229,0.958 3.385,1.156 0.156,0.198 10 false 4 1.229,0.948 1.385,1.146 0.156,0.198 10 false 1 5.083,0.646 5.521,1.146 0.438,0.5 10 false Switch Input Circuit 1.427,1.656 5.094,1.854 3.667,0.198 10 false Back Door Control Switch

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Back Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PBD Close SW Back door control switch signal ON or OFF ON: Back door control switch pushed
OFF: Back door control switch not pushed
-
Body Electrical > Back Door > Data List
Tester Display
PBD Close SW
50003 159 8
OK:

On GTS screen, item changes between ON and OFF according to above chart.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

2.INSPECT BACK DOOR CONTROL SWITCH
2.INSPECT BACK DOOR CONTROL SWITCH
a.

Remove the back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the back door control switch.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (BACK DOOR CONTROL SWITCH - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)
a.

Disconnect the V20 back door control switch connector.


b.

Disconnect the V12 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V20-4 - V12-4 (BDDN) Always Below 1 Ω
V20-1 - Body ground Always Below 1 Ω
V20-4 or V12-4 (BDDN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR