68131
1.CLEAN BACK DOOR GLASS
When reusing the back door glass:
Using a scraper, remove the spacers, clips, moulding, adhesive and double-sided tape on the back door glass.
Do not damage the back door glass.
Clean the outer edges of the back door glass with non-residue solvent.
Even if using a new back door glass, clean it with non-residue solvent.
64828
2.INSTALL BACK WINDOW GLASS CLIP LH
Apply Primer G to the back window glass clip LH installation area on the back door glass.
Do not apply too much Primer G.
Remove the peeling paper and install a new back window glass clip LH.
| *1 | Back Window Glass Clip LH |
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the back window glass clip LH to the back door glass in the location shown in the illustration.
Install the back window glass clip LH after Primer G has been allowed to dry (approximately 3 minuts).
64827A
3.INSTALL BACK WINDOW GLASS CLIP RH
Use the same procedure as for the back window glass clip LH.
64819
4.INSTALL NO. 2 BACK WINDOW GLASS SPACER
Apply Primer G to the No. 2 back window glass spacer installation area on the back door glass.
Do not apply too much Primer G.
Remove the peeling paper and install a new No. 2 back window glass spacer.
| *1 | No. 2 Back Window Glass Spacer |
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the No. 2 back window glass spacer to the back door glass in the location shown in the illustration.
Install the No. 2 back window glass spacer after Primer G has been allowed to dry (approximately 3 minuts).
64818B
5.INSTALL NO. 1 BACK WINDOW GLASS SPACER
Use the same procedure as for the No. 2 back window glass spacer.
62785F
6.INSTALL BACK DOOR GLASS SPACER
Apply Primer G to the back spacer installation area of the back door glass.
Do not apply too much Primer G.
Remove the peeling paper and install a new back door glass spacer.
| *1 | Back Door Glass Spacer |
| *a | Back Side of Back Door Glass |
| *b | Ceramic Notch |
Install the back door glass spacer to the back door glass in the location shown in the illustration.
Install the back door glass spacer after Primer G has been allowed to dry (approximately 3 minuts).
75571F
7.INSTALL BACK DOOR WINDOW MOULDING LH
Apply Primer G to the back door window moulding LH installation area of the back door glass.
Do not apply too much Primer G.
| *a | Back Side of Back Door Glass | - | - |
| Area | Measurement |
|---|---|
| a | 11.0 mm (0.433 in.) |
| b | 20.2 mm (0.795 in.) |
Remove the peeling paper and install a new back door window moulding LH.
Install the back door window moulding LH to the back door glass in the location shown in the illustration.
Install the back door window moulding LH after Primer G has been allowed to dry (approximately 3 minuts).
| *a | Back Side of Back Door Glass | - | - |
| Area | Measurement |
|---|---|
| a | 8.0 mm (0.315 in.) |
| b | 20.2 mm (0.795 in.) |
75571F
8.INSTALL BACK DOOR WINDOW MOULDING RH
Use the same procedure as for the back door window moulding LH.
75813C
9.INSTALL BACK DOOR OUTSIDE MOULDING CLIP
Apply Primer G to the back door outside moulding clip installation area of the back door glass.
Do not apply too much Primer G.
| *a | Back Side of Back Door Glass | *b | Ceramic Line |
|
Primer G | - | - |
Apply adhesive to the location shown in the illustration and install the back door outside moulding clip to the back door glass in the location shown in the illustration.
| *1 | Back Door Outside Moulding Clip | - | - |
| *a | Back Side of Back Door Glass | *b | Ceramic Line |
|
Adhesive | - | - |
Install the back door outside moulding clip after Primer G has been allowed to dry (approximately 3 minuts).
Using a scraper, remove any excess adhesive or apply as necessary.
Apply adhesive up to the edge of the windshield glass.
75813F
10.INSTALL NO. 1 BACK DOOR MOULDING CLIP
Apply Primer G to the No. 1 back door moulding clip installation area of the back door glass.
Do not apply too much Primer G.
| *a | Back Side of Back Door Glass | *b | Ceramic Line |
|
Primer G | - | - |
Apply adhesive to the location shown in the illustration and install the 14 No. 1 back door moulding clips to the back door glass in the location shown in the illustration.
| *1 | No. 1 Back Door Moulding Clips | - | - |
| *a | Back Side of Back Door Glass | *b | Ceramic Line |
|
Adhesive | - | - |
Install the No. 1 back door outside moulding clips after Primer G has been allowed to dry (approximately 3 minuts).
Using a scraper, remove any excess adhesive or apply as necessary.
Apply adhesive up to the edge of the windshield glass.
75573B
11.INSTALL BACK WINDOW OUTSIDE MOULDING
After the adhesive hardens, attach the claw to install the back window outside moulding.
| *a | Lower Side | - | - |
Attach the lower side of the claw first.
68131
12.INSTALL BACK DOOR GLASS
| *1 | Vehicle Body |
|
Adhesive |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.
Back door glass preliminary installation procedures.
Install the suction cups to the back door glass.
Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and the upper portion and sides of the back door glass is even.
| *a | Matchmarks |
Place adhesive tape on the back door glass and body panel and use a pen to place matchmarks for installation (when using a new back door glass).
When reusing a back door glass, check the position of the matchmarks and make adjustments.
Remove the back door glass.
Apply Primer M to the exposed panel surface of the back door panel.
Do not apply too much Primer M.
Do not apply Primer M to the adhesive.
Be careful when applying primer to the panel joints and spot welds.
Apply Primer G to the back door glass in the locations shown in the illustration.
| *a | Back Side of Back Door Glass | *b | Adhesive Application Center Line |
|
Primer G Application Area | - | - |
| Area | Measurement |
|---|---|
| a | 7.0 mm (0.276 in.) |
| b | 8.0 mm (0.315 in.) |
If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.
Allow Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
| *1 | Sealer Gun |
| *2 | Nozzle |
Cut off the tip of a cartridge nozzle as shown in the illustration.
| Area | Measurement |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
Toyota Genuine Windshield Glass Adhesive or equivalent
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Apply a bead of adhesive to the location shown in the illustration.
Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).
Load a sealer gun with the cartridge.
Apply a bead of adhesive to the location shown in the illustration.
| *a | Back Side of Back Door Glass | *b | Adhesive Application Center Line |
|
Adhesive | - | - |
| Area | Measurement |
|---|---|
| a | 8.0 mm (0.315 in.) |
| b | 12.0 mm (0.472 in.) |
Allow the primer coating to dry for 3 minutes or more.
Check that the clips are attached to the vehicle body correctly.
Check the clearance between the vehicle body and glass.
Install the back door glass.
| *a | Matchmarks |
Using suction cups, position the back door glass so that the matchmarks are aligned and install the back door glass.
Install the back door glass after Primer M on the back door panel has been allowed to dry (approximately 3 minuts).
Lightly press the back door glass from outside the vehicle so that it is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
Using a scraper, remove any excess adhesive or apply as necessary.
Apply adhesive up to the edge of the back door glass.
Do not drive the vehicle within the time written in the table below.
| Temperature | Minimum Time Prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Remove any excess adhesive before it hardens.
Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.
|
Bolt |
|
Connector |
Attach the clamp and claw.
Connect the connector and install the bolt.
68131
13.CHECK FOR BACK DOOR GLASS
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
Remove any protective or adhesive tape.
14.INSTALL REAR SPOILER ASSEMBLY
64886B
15.INSTALL BACK DOOR GLASS CHANNEL LH
64885C
16.INSTALL BACK DOOR GLASS CHANNEL RH
Use the same procedure as for the LH side.
85143R
17.INSTALL REAR WIPER MOTOR GROMMET
85110R
18.INSTALL REAR WIPER MOTOR ASSEMBLY
19.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
85292A
20.INSTALL REAR WIPER ARM HEAD CAP
67750
21.INSTALL BACK DOOR TRIM BOARD ASSEMBLY
74811D
22.INSTALL DOOR PULL HANDLE
67938A
23.INSTALL BACK DOOR SIDE GARNISH LH
67937B
24.INSTALL BACK DOOR SIDE GARNISH RH
67939B
25.INSTALL CENTER BACK DOOR GARNISH