Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0210090 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C165474E09
1.469,2.583 1.865,2.792 0.396,0.208 10 false G49 1.469,2.74 1.802,2.896 0.333,0.156 10 false ECM 1.438,4.24 1.74,4.448 0.302,0.208 10 false G7 5.906,4.771 6.344,4.969 0.438,0.198 10 false G46 5.917,4.938 6.813,5.333 0.896,0.396 10 false Airbag Sensor Assembly 0.521,5.365 2.292,5.531 1.771,0.167 10 false : CAN Communication Line 1.125,3.573 1.292,3.75 0.167,0.177 10 false 4 2.073,3.604 2.281,3.781 0.208,0.177 10 false 13 1.313,3.698 1.573,3.969 0.26,0.271 10 false CG 1.781,3.698 2.156,3.927 0.375,0.229 10 false TC 1.583,0.698 1.979,0.885 0.396,0.188 10 false CANL 1.563,1.24 1.979,1.385 0.417,0.146 10 false CANH 6.052,0.698 6.448,0.885 0.396,0.188 10 false CANL 6.052,1.24 6.469,1.385 0.417,0.146 10 false CANH 1.781,1.813 2.031,1.979 0.25,0.167 10 false TC 2.083,0.573 2.406,0.792 0.323,0.219 10 false 28 2.083,1.135 2.396,1.354 0.313,0.219 10 false 17 2.094,1.708 2.396,1.948 0.302,0.24 10 false 25 5.75,0.563 6,0.74 0.25,0.177 10 false 22 5.75,1.115 6.021,1.354 0.271,0.24 10 false 13 1.438,4.417 2.156,4.656 0.719,0.24 10 false DLC3

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM


Result:
Proceed to
DTCs are output
DTC is not output



DTCs are output

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.
C342737C01
1.448,0.354 1.813,0.573 0.365,0.219 1.531,2.833 1.896,3.052 0.365,0.219 1.531,2.083 1.76,2.083 1.76,2.083 2.083,1.521 true 1.25,4.375 1.479,4.375 1.479,4.375 1.802,3.813 true 1.5,0.385 1.958,0.583 0.458,0.198 10 false G49 1.333,2 1.646,2.198 0.313,0.198 10 false TC 1.052,4.292 1.365,4.49 0.313,0.198 10 false TC 1.625,2.865 2.083,3.063 0.458,0.198 10 false G7 0.885,0.188 1.198,0.385 0.313,0.198 10 false *a 0.917,2.531 1.229,2.729 0.313,0.198 10 false *b
*a Rear view of wire harness connector (to ECM)
*b Front view of DLC3


Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-25 (TC) - G7-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C23
1.458,0.281 1.844,0.51 0.385,0.229 1.635,0.917 2.094,0.531 2.094,0.531 2.24,0.531 true 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 2.313,0.458 2.594,0.646 0.281,0.188 10 false CG 1.573,0.313 1.865,0.458 0.292,0.146 10 false G7
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C342738C01
1.469,0.302 1.875,0.521 0.406,0.219 1.542,0.333 2,0.531 0.458,0.198 10 false G49 1,0.104 1.313,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G49-25 (TC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU