Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

When the trigger switch is pressed, the certification ECU (smart key control ECU assembly) generates a request signal and sends it through the front door outside handle assembly (for Front Passenger Door) (electrical key antenna).

The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the front passenger side door in order to detect the person carrying the electrical key transmitter sub-assembly.

DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Front Passenger Door) (between terminals CLG6 and ANT1, or terminals CG6B and ANT2).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A2 Open in Front Passenger Side Electrical Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Front Passenger Door) (CLG6 - ANT1, CG6B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
·

Harness or connector

·

Front door outside handle assembly (for Front Passenger Door)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Vehicle Condition when Malfunction Detected
Entry lock/unlock operation cannot be performed for front passenger door -

Related Data List and Active Test
DTC No. Data List and Active Test
B27A2 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B405295E02
5.094,2.573 6.604,3.146 1.51,0.573 10 false Certification ECU (Smart Key ECU Assembly) 4.938,2.021 5.25,2.229 0.313,0.208 10 false G17 4.948,0.865 5.26,1.073 0.313,0.208 10 false G17 6.5,2.021 6.813,2.229 0.313,0.208 10 false G16 6.531,1.802 6.844,2.01 0.313,0.208 10 false 10 5.823,1.177 6.135,1.385 0.313,0.208 10 false IC 5,1.771 5.313,1.979 0.313,0.208 10 false 27 4.99,0.635 5.302,0.844 0.313,0.208 10 false 26 5.302,0.75 6.063,1 0.76,0.25 10 false CLG6 5.313,1.885 6.073,2.135 0.76,0.25 10 false CG6B 1.333,1.927 2.094,2.177 0.76,0.25 10 false ANT2 1.323,0.771 2.083,1.021 0.76,0.25 10 false ANT1 1.813,0.781 2.125,0.99 0.313,0.208 10 false 3 1.833,1.927 2.146,2.135 0.313,0.208 10 false 6 0.74,2.542 1.052,2.75 0.313,0.208 10 false K8 0.729,2.719 3.031,3.198 2.302,0.479 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 6.292,2.021 7.052,2.271 0.76,0.25 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for Front Passenger Door).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect K8 front door outside handle assembly (for Front Passenger Door) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-26 (CLG6) - K8-3 (ANT1) Always Below 1 Ω
G17-27 (CG6B) - K8-6 (ANT2) Always Below 1 Ω
G17-26 (CLG6) or K8-3 (ANT1) - Body ground Always 10 kΩ or higher
G17-27 (CG6B) or K8-6 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Connect the G17 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B418156C02
2.5,0.365 2.927,0.594 0.427,0.229 4.385,0.375 4.813,0.604 0.427,0.229 2.854,4.458 3.01,4.458 3.01,4.458 3.302,3.76 true 1.719,2.01 1.875,2.01 1.875,2.01 2.167,1.313 true 4.25,2.042 4.49,2.042 4.49,2.042 4.792,1.406 true 5.646,2.094 5.385,2.094 5.385,2.094 4.854,1.396 true 0.271,0.156 0.583,0.313 0.313,0.156 10 false *a 2.563,2.875 2.875,3.031 0.313,0.156 10 false *b 2.646,4.365 2.958,4.521 0.313,0.156 10 false *c 2.583,0.385 2.927,0.573 0.344,0.188 10 false G16 4.479,0.396 4.823,0.583 0.344,0.188 10 false G17 2.313,3.615 2.76,3.771 0.448,0.156 10 false GND 1.573,1.906 1.917,2.094 0.344,0.188 10 false E 3.823,1.948 4.385,2.146 0.563,0.198 10 false CG6B 5.719,2.031 6.281,2.229 0.563,0.198 10 false CLG6
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Trigger switch ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
G17-26 (CLG6) - G16-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door).


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
G17-27 (CG6B) - G16-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door).


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
a.

Replace the front door outside handle assembly (for Front Passenger Door) with a new one or the front door outside handle assembly (for Driver Door) if it is functioning properly.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A2 is not output.



Result:
Proceed to
OK
NG



OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)