The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door disassembly/reassembly are shown below.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
Fully open the front door glass sub-assembly RH before proceeding with work.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67491A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH RH
Detach the clip and claw and remove the front door lower frame bracket garnish RH.
74210
4.REMOVE FRONT ARMREST ASSEMBLY RH
|
Place Hands Here |
|
Order of Removal |
|
Remove in this Direction |
Detach the clip and claw and remove the front armrest assembly RH as shown in the illustration.
5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
|
Remove in this Direction |
Detach the clip and claw.
Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.
84870A
6.REMOVE OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)
84820
7.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)
8.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
|
Remove in this Direction |
Detach the clip and claw.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
84810
9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
81230
10.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
67665C
11.REMOVE FRONT DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)
| *A | for RH side |
| *B | for LH side |
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Put protective tape around the reflex reflector.
Using a thin-bladed screwdriver, detach the claw and guide.
Tape the thin-bladed screwdriver tip before use.
Remove the front door trim reflector RH.
69283
12.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG RH
Using moulding remover A, detach the claw and remove the front door inside handle bezel plug RH as shown in the illustration.
67601
13.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH
Remove the 3 screws.
|
Place Hands Here |
|
Order of Removal (1) |
|
Order of Removal (2) |
|
Remove in this Direction |
Detach the clip as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the front door trim board sub-assembly RH as shown in the illustration.
| *1 | Front Door Inside Looking Cable Assembly RH |
| *2 | Front Door Lock Remote Control Cable Assembly RH |
|
Remove in this Direction |
Detach the clamp and disconnect the front door lock remote control cable assembly RH and front door inside looking cable assembly RH as shown in the illustration.
69205
14.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY RH
|
Remove in this Direction |
Detach the claw and guide and remove the front door inside handle sub-assembly RH from the front door trim board sub-assembly RH.
68171B
15.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP RH
Raise the claw of the front door inner glass weatherstrip RH as shown in the illustration, and then remove the front door inner glass weatherstrip RH from the front door trim board sub-assembly RH.
86160
16.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
86160P
17.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY
89865
18.REMOVE DOOR SIDE AIR BAG SENSOR RH
87910
19.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
67831
20.REMOVE FRONT DOOR SERVICE HOLE COVER RH
|
Butyl Tape |
Remove the ground bolt and disconnect the ground wire.
Detach the clamp.
Pull out the front door lock remote control cable assembly RH, front door inside locking cable assembly RH and wire harness from the front door service hole cover RH, and then remove the front door service hole cover RH.
Remove any remaining butyl tape from the front door panel.
21.REMOVE SCREW GROMMET
Using a clip remover, detach the claw and remove the 2 screw grommets.
68141C
22.REMOVE FRONT DOOR GLASS RUN RH
Detach the guide and remove the front door glass run RH.
68101
23.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY RH
Temporarily install the power window regulator master switch assembly.
Connect the cable to the negative (-) battery terminal.
Move the front door window regulator sub-assembly RH so that the front door glass sub-assembly RH bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Remove the power window regulator master switch assembly.
Remove the 2 bolts.
Be careful when removing the bolts as the glass may fall and become damaged.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly RH as shown in the illustration.
Be careful not to damage the glass.
67403F
24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY RH
Remove the bolt.
Detach the guide and remove the front door rear lower frame sub-assembly RH.
69801
25.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY RH
Disconnect the connector.
Loosen the temporarily bolt.
Do not remove the temporarily bolt. If the temporarily bolt is removed, the front door window regulator sub-assembly RH may fall and become damaged.
|
Bolt |
|
Connector |
|
Temporarily Bolt |
Remove the 5 bolts and front door window regulator sub-assembly RH.
Remove the temporarily bolt from the front door window regulator sub-assembly RH.
85710D
26.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
| *1 | Hole Plug |
|
Remove in this Direction |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
69217D
28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
|
Protective Tape |
|
Remove in this Direction |
Using a thin-bladed screwdriver, detach the claw and guide and remove the front door outside handle cover from the lock cylinder assembly as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
69217D
29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
| *1 | Hole Plug |
|
Remove in this Direction |
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the claw and remove the front door outside handle cover as shown in the illustration.
69310
30.REMOVE FRONT DOOR LOCK ASSEMBLY RH
69035A
31.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY RH
69750C
32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY RH
69710B
33.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH
69318C
34.REMOVE DOOR LOCK WIRING HARNESS SEAL
69210
35.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH
w/ Smart Entry and Start System:
|
Protective Tape |
|
Remove in this Direction |
Using a thin-bladed screwdriver, detach the claw and open the connector cover as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and disconnect the connector and connector cover.
Tape the thin-bladed screwdriver tip before use.
|
Remove in this Direction |
Remove the front door outside handle assembly RH as shown in the illustration.
69241H
36.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the front door front outside handle pad.
69242E
37.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the front door rear outside handle pad.
69201A
38.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH
| *a | Grommet |
| *b | Guide |
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the grommet and guide and remove the front door outside handle frame sub-assembly RH together with the wire harness.
w/ Smart Entry and Start System:
| *a | Clamp |
| *b | Guide |
Detach the clamp and guide, disconnect the wire harness and remove the front door outside handle frame sub-assembly RH.
69311A
39.REMOVE FRONT DOOR LOCK OPEN ROD RH
|
Remove in this Direction |
Detach the snap and remove the front door lock open rod RH from the front door outside handle frame sub-assembly RH as shown in the illustration.
75710
40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL
67837B
41.REMOVE FRONT DOOR DUST PROOF SEAL
Detach the claw and remove the 3 front door dust proof seals.
67001A
42.REMOVE FRONT DOOR PANEL CUSHION
Detach the claw and remove the 2 front door panel cushions.
68610B
43.REMOVE FRONT DOOR CHECK ASSEMBLY RH
|
Bolt (A) |
|
Bolt (B) |
Remove the 2 bolts (A), bolt (B) and front door check assembly RH.
67861
44.REMOVE FRONT DOOR WEATHERSTRIP RH
Using a clip remover, detach the clip and remove the front door weatherstrip RH.
75921C
45.REMOVE NO. 1 BLACK OUT TAPE RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>REMOVAL