Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

When there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly).


·

Certification ECU (smart key ECU assembly)

·

ECM

·

Harness or connector


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799 -

WIRING DIAGRAM

E318146E07
5.083,0.99 5.698,1.188 0.615,0.198 10 false EFII 5.083,1.885 5.698,2.083 0.615,0.198 10 false EFIO 4.646,1.104 5.26,1.302 0.615,0.198 10 false G16 4.729,0.875 5.344,1.073 0.615,0.198 10 false 3 4.646,2.01 5.26,2.208 0.615,0.198 10 false G17 4.698,1.792 5.313,1.99 0.615,0.198 10 false 35 2.333,0.99 3.021,1.167 0.688,0.177 10 false 17 2.344,1.896 3.094,2.042 0.75,0.146 10 false 16 1.948,0.979 2.563,1.177 0.615,0.198 10 false IMO 2,1.885 2.615,2.083 0.615,0.198 10 false IMI 6,0.323 6.615,0.521 0.615,0.198 10 false +B 1.76,1.563 2.375,1.76 0.615,0.198 10 false +B 5.052,2.938 6.594,3.406 1.542,0.469 10 false Certification ECU (Smart Key ECU Assembly) 1.031,2.927 2.135,3.125 1.104,0.198 10 false G50 1.042,3.104 1.656,3.302 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799 is not output.



Result:
Result Proceed to
OK A
NG (DTC B2799 is output) B
NG (Other DTCs are output) C



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

4.INSPECT ECM (TERMINAL IMO)

C

4.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

E317803C03
0.521,0.625 0.958,0.844 0.438,0.219 1.667,0.625 2.104,0.844 0.438,0.219 2.802,0.615 3.24,0.833 0.438,0.219 3.854,0.615 4.292,0.833 0.438,0.219 4.969,0.615 5.406,0.833 0.438,0.219 6.104,0.604 6.542,0.823 0.438,0.219 5.771,2.073 5.917,1.438 true 0.604,0.677 0.938,0.865 0.333,0.188 10 false C38 1.76,0.677 2.094,0.865 0.333,0.188 10 false C39 2.896,0.667 3.229,0.854 0.333,0.188 10 false C40 3.948,0.656 4.281,0.844 0.333,0.188 10 false C41 5.052,0.646 5.385,0.833 0.333,0.188 10 false G49 6.198,0.635 6.531,0.823 0.333,0.188 10 false G50 2.938,4.104 3.271,4.292 0.333,0.188 10 false *b 0.26,0.104 0.594,0.292 0.333,0.188 10 false *a 5.625,2.146 5.958,2.333 0.333,0.188 10 false IMO 0.927,4.052 1.427,4.25 0.5,0.198 10 false GND
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G50-17 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected

OK:

The waveform is similar to that shown in the illustration.



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Terminal IMO stuck high (12 V) or abnormal waveform C



A

5.INSPECT ECM (TERMINAL IMI)

B

11.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

8.REPLACE ECM
5.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

E317804C03
0.594,0.448 1.063,0.677 0.469,0.229 1.667,0.448 2.135,0.677 0.469,0.229 2.813,0.448 3.281,0.677 0.469,0.229 3.885,0.448 4.354,0.677 0.469,0.229 5.063,0.448 5.531,0.677 0.469,0.229 6.146,0.448 6.615,0.677 0.469,0.229 5.708,1.99 6.042,1.302 true 0.167,0.094 0.479,0.25 0.313,0.156 10 false *a 3.354,4.125 3.667,4.281 0.313,0.156 10 false *b 0.948,4.052 1.417,4.208 0.469,0.156 10 false GND 0.698,0.49 1.031,0.656 0.333,0.167 10 false C38 1.781,0.5 2.115,0.667 0.333,0.167 10 false C39 2.958,0.5 3.292,0.667 0.333,0.167 10 false C40 4,0.5 4.333,0.667 0.333,0.167 10 false C41 5.156,0.5 5.49,0.667 0.333,0.167 10 false G49 6.25,0.5 6.583,0.667 0.333,0.167 10 false G50 5.583,2.031 5.917,2.198 0.333,0.167 10 false IMI
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection G50-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected


OK:

The waveform is similar to that shown in the illustration.


Result:
Proceed to
OK
NG



OK

6.REGISTER ECU COMMUNICATION ID

NG

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
6.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE ECM
8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.
E317805C03
1.521,0.385 1.948,0.656 0.427,0.271 2.938,2.167 2.615,1.719 true 0.115,0.198 0.427,0.354 0.313,0.156 10 false *a 1.604,0.448 2.073,0.656 0.469,0.208 10 false G50 2.844,2.208 3.313,2.417 0.469,0.208 10 false IMO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Result
G50-17 (IMO) - Body ground Engine switch on (IG) using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

8.REPLACE ECM
12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the G50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-3 (EFII) - G50-17 (IMO) Always Below 1 Ω
G17-35 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-17 (IMO) - Body ground Always 10 kΩ or higher
G16-3 (EFII) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G17-35 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Recognition code registration is necessary when replacing the certification ECU (smart key ECU assembly).

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch was turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG