Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2015.08–2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212882 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B416730E04
1.979,0.896 2.438,1.094 0.458,0.198 10 false IMO 2.01,1.802 2.469,2 0.458,0.198 10 false IMI 1.802,1.49 2.26,1.688 0.458,0.198 10 false +B 1.271,3.01 1.729,3.208 0.458,0.198 10 false ECM 1.25,2.844 1.708,3.042 0.458,0.198 10 false G50 2.344,1.792 2.802,1.99 0.458,0.198 10 false 16 2.333,0.885 2.792,1.083 0.458,0.198 10 false 17 4.729,0.896 5.188,1.094 0.458,0.198 10 false 12 4.75,1.792 5.208,1.99 0.458,0.198 10 false 13 5.063,0.896 5.521,1.094 0.458,0.198 10 false EFII 5.042,1.792 5.5,1.99 0.458,0.198 10 false EFIO 6.042,0.24 6.26,0.458 0.219,0.219 10 false +B 4.938,2.865 5.396,3.063 0.458,0.198 10 false G127 4.948,3.042 7.031,3.229 2.083,0.188 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine > Trouble Codes
50001 234
OK:

DTC is not output.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK WHETHER ENGINE STARTS

B

3.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK ECM (TERMINAL IMI)
4.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B427162C01
0.521,0.25 0.958,0.49 0.438,0.24 1.719,0.25 2.156,0.49 0.438,0.24 2.906,0.25 3.344,0.49 0.438,0.24 3.906,0.25 4.344,0.49 0.438,0.24 5.021,0.25 5.458,0.49 0.438,0.24 6.146,0.25 6.583,0.49 0.438,0.24 6.375,1.542 6.052,0.979 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 2.365,3.771 2.677,3.927 0.313,0.156 10 false *b 0.615,0.302 1.073,0.5 0.458,0.198 10 false C38 1.823,0.302 2.281,0.5 0.458,0.198 10 false C39 2.99,0.292 3.448,0.49 0.458,0.198 10 false C40 3.99,0.292 4.448,0.49 0.458,0.198 10 false C41 5.115,0.302 5.573,0.5 0.458,0.198 10 false G49 6.25,0.302 6.708,0.5 0.458,0.198 10 false G50 6.333,1.594 6.854,1.854 0.521,0.26 10 false IMI 0.979,3.656 1.5,3.917 0.521,0.26 10 false GND
*a Component with harness connected
(ECM)
*b Waveform A


Item Content
Terminal No. (Symbol) G50-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B




A

5.CHECK ECM (TERMINAL IMO)

B

13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
5.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B427163C01
0.552,0.24 0.99,0.479 0.438,0.24 1.688,0.24 2.125,0.479 0.438,0.24 2.896,0.229 3.333,0.469 0.438,0.24 3.917,0.229 4.354,0.469 0.438,0.24 5.031,0.219 5.469,0.458 0.438,0.24 6.188,0.219 6.625,0.458 0.438,0.24 5.531,1.771 5.938,0.99 true 0.031,0.031 0.344,0.188 0.313,0.156 10 false *a 2.948,2.729 3.26,2.885 0.313,0.156 10 false *b 2.594,3.792 2.906,3.948 0.313,0.156 10 false *c 3.031,3.75 3.344,3.906 0.313,0.156 10 false *d 0.667,0.271 1.125,0.469 0.458,0.198 10 false C38 1.802,0.292 2.26,0.49 0.458,0.198 10 false C39 3.01,0.271 3.469,0.469 0.458,0.198 10 false C40 4.01,0.271 4.469,0.469 0.458,0.198 10 false C41 5.146,0.271 5.604,0.469 0.458,0.198 10 false G49 6.313,0.26 6.771,0.458 0.458,0.198 10 false G50 0.99,3.646 1.448,3.844 0.458,0.198 10 false GND 5.375,1.813 5.833,2.01 0.458,0.198 10 false IMO
*a Component with harness connected
(ECM)
*b Waveform B
*c Approximately 160 ms *d Approximately 270 ms


Item Content
Terminal No. (Symbol) G50-17 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform B not output, or has abnormal wavelength or shape B




A

6.CHECK ECM (TERMINAL IMI)

B

6.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B427164C01
0.563,0.208 0.979,0.49 0.417,0.281 1.708,0.208 2.125,0.49 0.417,0.281 2.875,0.208 3.292,0.49 0.417,0.281 3.938,0.208 4.354,0.49 0.417,0.281 5.094,0.208 5.51,0.49 0.417,0.281 6.167,0.208 6.583,0.49 0.417,0.281 6.208,1.677 6.042,0.99 true 0.052,0.073 0.365,0.229 0.313,0.156 10 false *a 3.354,2.656 3.667,2.813 0.313,0.156 10 false *b 3.063,3.729 3.375,3.885 0.313,0.156 10 false *c 3.667,3.698 3.979,3.854 0.313,0.156 10 false *d 0.646,0.26 1.104,0.458 0.458,0.198 10 false C38 1.813,0.271 2.271,0.469 0.458,0.198 10 false C39 2.979,0.271 3.438,0.469 0.458,0.198 10 false C40 4.052,0.281 4.51,0.479 0.458,0.198 10 false C41 5.177,0.292 5.635,0.49 0.458,0.198 10 false G49 6.271,0.281 6.729,0.479 0.458,0.198 10 false G50 6.167,1.719 6.625,1.917 0.458,0.198 10 false IMI 1.042,3.656 1.5,3.854 0.458,0.198 10 false GND
*a Component with harness connected
(ECM)
*b Waveform C
*c Approximately 160 ms *d Approximately 270 ms


Item Content
Terminal No. (Symbol) G50-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform C not output, or has abnormal wavelength or shape B




A

7.REGISTER ECU COMMUNICATION ID

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
7.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER KEY
10.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

11.REGISTER ECU COMMUNICATION ID
11.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

13.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G127 transponder key ECU assembly connector.


b.

Disconnect the G50 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-13 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G127-13 (EFIO) - Body ground Always 10 kΩ or higher
G50-16 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR