The skid control ECU assembly is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation.
If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.
When the 4WD control switch (transfer position switch) set to L4, VSC is prohibited and the VSC OFF indicator light turns on.
When the rear differential is locked, VSC is prohibited, and the VSC OFF and TRC OFF indicator lights turn on.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
As there may be malfunctions in the touch select 2-4 and high-low system related to when the transfer operates in L4, check the touch select 2-4 and high-low system first.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Check if the skid control ECU assembly (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A4 skid control ECU (brake actuator assembly) connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC/VSC Off Mode | TRC/VSC off mode | Normal, TRC OFF, Unknown or VSC OFF | Normal: Normal mode
TRC OFF: TRC off mode VSC OFF: VSC off mode |
Unknown: Unspecified |
| Tester Display |
|---|
| TRC/VSC Off Mode |
Check that the indicator light and mode condition on the GTS change according to VSC OFF switch operation.
| Switch Operation | Mode Condition Display | Multi-information Display (TRC OFF Message) | VSC OFF Indicator Light |
|---|---|---|---|
| Not pressed | Normal | Not displayed | Does not come on |
| Pressing the VSC OFF switch | TRC OFF | Displayed | Does not come on |
| Pressing and holding the VSC OFF switch | VSC OFF | Displayed | Comes on |
| Result | Proceed to |
|---|---|
| Indicator light and mode condition display do not change. | A |
| Mode condition display is normal, but indicator light does not change. | B |
| Indicator light and mode condition display are normal. | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.
Check for DTCs.
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output |
DTCs are not output
DTCs are output
Select the Active Test on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| TRC(TRAC) OFF Indicator Light | Multi-information display (TRC OFF message) | Display ON/OFF | Observe combination meter assembly
Vehicle condition: Vehicle stopped |
| VSC OFF Indicator Light | VSC OFF indicator light | Indicator light ON/OFF | Observe combination meter assembly
Vehicle condition: Vehicle stopped |
| Tester Display |
|---|
| TRC(TRAC) OFF Indicator Light |
| Tester Display |
|---|
| VSC OFF Indicator Light |
Check the multi-information display (TRC OFF message) and VSC OFF indicator light on the combination meter assembly turn ON or OFF in accordance with the GTS operation.
The multi-information display (TRC OFF message) and VSC OFF indicator light turn ON or OFF in accordance with the GTS operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Remove the VSC OFF switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL
Inspect the VSC OFF switch.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION
The VSC OFF switch operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A4-33 (CSW) - G23-6 | Always | Below 1 Ω |
| A4-33 (CSW) or G23-6 - Body ground | Always | 10 kΩ or higher |
| G23-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the Active Test of the combination meter assembly using the GTS.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display |
|---|
| Meter Display 1 |
| Tester Display |
|---|
| Indicat. VSC OFF |
Check the combination meter assembly.
The multi-information display and VSC OFF indicator light turns on or off in accordance with the GTS operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING